KJ-01.02.Instruction Manual.REV.02.pdf - 第401页

5 On Program Editing Error No. Error Message Correctiv e Action E2000 Bad letter(s) in specified data. This error message appears on the screen when you enter an alphabetic character for the item for which a numeric char…

On Printing

Error No. Error Message Corrective Action

E0810 Production data was not exists. Any production program has not been loaded into the

machine. Load the production program file to be printed to

the machine, and print it.

E0811 No production information data. This error message appears on the screen when you try to

print production information with a production program that

has never been used for production. Use the production

program that was used for production to perform the printing

function again.

E0814 Input value too small. This error message appears on the screen if the number

specified as the printing end number is smaller than that of

the printing start number to specify the production program

print mode.

Set the correct number.

E0815 Input value too big. This error message appears on the screen if the number

specified as the printing start number is larger than that of

the printing end number to specify the production program

print mode.

Set the correct number.

E0816 Input value illegal. This error message appears on the screen when you are to

enter a character other than a numeric character in the edit

box to set the production-program printing mode. Allowable

characters are numeric characters only. Enter a correct

value.

E100003 Environment file error

Cannot read printer setting file

pass.

Any printer-setting file or directory may not be created

correctly. Check to see if a directory for a printer-setting file

is created correctly.

E100006 Environment file error.

Not found environment file.

The printer-setting file may be lost.

Check to see if the printer-setting file is created correctly.

E100100 Didn't setup for japanese

environment.

The printer-setting file may be damaged and the setting

necessary for the Japanese environment may not be loaded

to the machine.

Check to see if the printer-setting file is created correctly.

None Printer connect error.

Printer's paper empty. or can't print

status.

The printer may run out of paper.

Replenish the printer with paper to enable it to print data.

Press the <Re-try> switch to resume printing.

None Printer connect error.

Not connect to printer. Confirm

connection to printer.

The printer may not be enabled to print data. Check to see

if the printer is turned on or enter Offline mode.

On Program Editing

Error No. Error Message Corrective Action

E2000 Bad letter(s) in specified data. This error message appears on the screen when you enter

an alphabetic character for the item for which a numeric

character should be entered. Check to see what type of

characters can be entered for each item, and enter

appropriate type of data.

E2001 Input data range over. Can not

set.

You entered data that exceeded the range regulated for the

item.

Enter data that is within the range

E2004 No items selected. This error message appears on the screen if you select the

item that cannot be set: for example, when you select a

BOC for a matrix circuit even though you already selected a

single-plane board (“Single PWB” as “PWB configuration”)

on the PWB data screen.

E2005 Numeric data required. This error message appears on the screen when you enter

an alphabetic character for an item for which you have to

enter a numeric character (on the PWB data screen).

Check the type of characters available to each item, and then

enter the correct type of character(s).

E2006 Data is nothing. This error message appears on the screen if you try to

operate data that does not exist actually. Only after data is

completely created, operate it.

E2007 Input is wrong. This error message appears on the screen when you enter a

space to register data to the mark database. Enter the

name to be registered.

E2101 Input data exceeds 400 circuits. The number of circuits of the multi-plane matrix board

exceeds 400 (maximum number of circuits). Set the

number of X- and Y-direction divisions so that the number of

circuits can be 400 or less.

E2102 Circuit reference position will be

range over.

The circuit origin of a matrix board exceeds the machine X-

and Y-direction movable range. Check the number of circuit

divisions, pitch, the first circuit position, and so on to enter

the correct origin.

E2103 Detail data is nothing. This error message appears on the screen if you have not

set the PWB positioning point to teach a BOC mark. (The

number of circuit divisions, the pitch and the first circuit

position have to be entered for a matrix board.)

Only after setting the PWB positioning point, teach a mark.

W2104 Mark teaching not end. An error occurred during BOC mark teaching operation.

Set a mark coordinate, forward/reverse rotation of the

recognized image data, scale frame, noise cut level, a mark

and inspection frame correctly.

E2200 PWB data is not finished yet. You tried to edit Placement, Component, and/or Pick data

although you have not completed PWB data.

Only after entering PWB data completely, edit another type of

data.

E2201 Placement data is full. Up to 2000 component placement points can be set for one

circuit. When you try to copy data or perform the [Duplicate]

command to create 2001 or more placement points on the

Placement data screen, this error message appears on the

screen. Be sure to set 2000 or less placement points.

E2202 Component ID is duplicated. This error message appears on the screen when the

component ID you are to set on the Placement data screen is

already used.

Note that upper case characters and lower case characters

are not distinguished to specify a component ID by the

system.

E2203 Component data is full. Up to 40 components can be set for one production

program. (This number is further limited by the feeder

installation position.) If you try to enter a new

component name although 40 components are already

entered on the Placement data screen, an error occurs.

Even though you press the ENTER key by mistake and

enter a component name as the result, memory space is

allocated with corresponding to this entered data. In

such a case, delete a component that is never placed on

a board on the Component list screen.

E2204 IC mark data is full. Up to 50 placement points are allowable for one circuit

when using an IC mark. If you try to create 51 or more

placement points that use an IC mark on the Placement

data screen, this error message appears on the screen.

E2205 '+=' can not be used in 1st line Although the machine allows you to enter coordinates

relative to the data one line above (by using the symbols

“+=“ or “-=”) on the Placement data screen, you cannot

enter data in this way on the top line.

E2206 No data in upper line. Only if data is entered to the same item one line above on

the Placement data screen, you can enter data that is

relative to that item to the current item (by using the

symbols “+=“ or “-=”).

E2207 No initial value. Only if you have already entered data to the

corresponding item on the Placement data screen, you

can enter data relative to that data to the current item (by

using the symbols “++” or “—“).

E2208 Not found component ID. **** The component ID “XXXXX” specified for searching

through Placement data does not exist. Check the

entered component ID.

E2209 Not found component name. **** The component name “XXXXX” specified for searching

through Placement data does not exist. Check the

entered component name.

E2210 No data to operate. This error message appears on the screen if there is no

completed data when you are to sort Placement data

using the nozzle name as the key, or if there is only one

completed data record and there is no data to be sorted.

E2211 Placement data is incomplete.

Sort will be aborted.

This error message appears on the screen if there is still

a not-completed placement data record when you are to

sort data using the nozzle name as the key.

E2212 Data is nothinhg. This error message appears on the screen when there is

no completed placement data or when you perform the

[Duplicate] command on the top line.

Complete two or more placement data records and

perform the [Duplicate] command on a line other than the

top line.

E2213 10,000 placements exceeded. This error message appears on the screen if the number

of component placement points of a matrix/non-matrix

board exceeds 10000. Set component placement points

as shown in the expression: (number of circuits:

maximum 400) * placement points <= 10000 (for a matrix

board) or (number of circuits: maximum 100) *

placement points <= 10000.

E2214 Placement or mark position is range

over.

The coordinates of a component placement point or of

mark point exceeds the machine X- and Y-direction mo

After checking the positioning point on the PWB data

screen and so on, set the placement point or mark point

within the range.vable range.

E2300 Placement data is not finished yet. You tried to edit Component data/Pick data although you

have not completed any Placement data record. Create

one or more Placement data record(s) completely.