Hanwha SM481 PLUS Series Administrator’s Guide Eng.pdf.pdf - 第323页
12-15 LED placement 12.4.3. Nozzle Figure12.5 “Opt imizer Setup: Nozzle” dialog box This dialog box shows the information on Nozzle a rrangement. <Nozzle Requiremen t > list box This list bo x indicates the typ e…
12-14
Fast Flexible Placer SM481(L) Administrator’s Guide
All arranged tape feeders can be removed by pressing the <Remove Tape> button
under the dialog box..
<Total Number of Feeder(s)> list box
For each feeder, the number of placement points, the number of arranged tape feeders,
and the number of tape feeders to be newly arranged are displayed in the list box on
the right and can be viewed at a glance.
<Component> column
The components to be supplied from tape feeders are all displayed here.
<Point> column
Displays the number of placement points for each component. This can be referred
to when deciding the number of feeders to be mounted.
<ARG> column
Displays the number of feeders already arranged on the feeder lane for each
component. This number coincides with the number of feeder lanes shown in the
list box on the right.
<AVL> column
Displays the number of feeders to be arranged by Optimizer for each component.
<LIM> column
Displays the sum of the feeders shown in ARG and AVL for each component. In
other words, it is the limited number of feeders that can be arranged for each
component. The minimum value is 1.
<Set> button
Used to specify the number of feeders to be arranged for each component. When there
is one feeder already arranged for a certain part, enter ‘3’ in the right edit box and click
this button. Then the number of <AVL> column becomes ‘2’.
Appropriate number of feeders must be set in consideration of the number of
placement points for each component. If the Optimizer considers that more than one
feeders are not necessary, it might not be used. .
To obtain good operation efficiency, a relatively large number of feeders must be
assigned to a component with many placement points.
button
Used to have the feeder selected in the <Arranged Feeders> list box to be arranged
again by Optimizer.
12-15
LED placement
12.4.3. Nozzle
Figure12.5 “Optimizer Setup: Nozzle” dialog box
This dialog box shows the information on Nozzle arrangement.
<Nozzle Requirement> list box
This list box indicates the types of nozzles necessary for the part placement as well as
the number of times of use of each nozzle.
<Nozzle> column
Displays the nozzle name.
<Placements> column
Displays the number of times each nozzle is used. In other words, the number of
placement points using the corresponding nozzle.
<# of Nozzles Arranged> list box
This list box indicates the types and number of nozzles that are arranged in each ANC
currently.
<Nozzle> column
Displays the nozzle name.
<ANC-1 ANC-2> column
Displays the ANC where the nozzle is arranged.
12-16
Fast Flexible Placer SM481(L) Administrator’s Guide
<Assign Nozzle> button
Used to assign applicable heads for each nozzle separately. When this button is clicked
on, the following dialog box is displayed.
Figure12.6 “Optimizer Setup: Assign Nozzle” dialog box
Basically all nozzle types can be applied to any head, therefore all heads are checked.
But there are occasions when a certain nozzle has to be operated in a certain head.
Also, this can be used when the user wants to assign a certain head to a certain nozzle.
The above figure shows the nozzle CN040 can operate on any head between Head1
and Head2012610.
<Useful Heads> check box group
The heads that can be used by the selected nozzle type. As a standard, check so that
Head1 ~ Head2012610 can be used.
<Mounting Points> group
This group shows the number of components used by the nozzle selected for the
current PCB. This can be used as a reference data when the user assigns the applicable
heads to each nozzle.
#1 shows the total number of placement points of the component for which #1 nozzle
is selected and #10 shows the total number of placement points of the component for
which #10 nozzle is selected.
Figure 10-3 shows that CN040 is selected for 1# nozzle of three components and for