Hanwha SM481 PLUS Series Administrator’s Guide Eng.pdf.pdf - 第462页
15-26 Fast Flexible Placer SM481(L) PLUS Administ r ator’s Guide Fiducial Mar k Dialog Box automatically . This dialog box d oes not appear when adjusting the fi du cial mark in the Step Dial og Box, but appears only whe…
15-25
System Setup
Memo For parts fed by an 8mm tape feeder, it is recommended that this
function be applied.
For parts fed by a tape feeder with tape larger than 8mm, if this
function is applied, the part dumping rate can be reduced. However,
do not use this function for parts with the following characteristics.
When a part moves significantly in the tape pocket.
When it is difficult to set the part pickup height accurately.
(Example: Same types of parts with a great variation in
thickness.)
<Pocket teach while the machine is working> check box
If this check box is selected, the Pocket Teach function is applied when picking up the
part supplied through the supplying device that was set to use the Pocket Teach in the
'Feeders' dialog box.
If this check box is selected, the edit box of the selected items is enabled right below it.
This edit box is used to adjust the tolerance when performing synchronized pickup.
At this time, the tolerance for the synchronized pickup is as follows:
Tolerance for synchronized pickup =Sync Pickup Tol +[Sync Pickup Tol X (a /100 )]
Sync Pickup Tolerance is that of the common data for the corresponding part.
'a' is the value entered into the edit box.
If the Sync Pickup Tolerance of the corresponding part is 15, and the value of 'a' is
67, the Sync Pickup Tolerance becomes 25.05%.
Sync Pickup Tolerance =15 +[15 X (67 /100 )] =25.05 %
<Bad mark check before Fiducial mark check> check box
If this button is checked, executes bad mark check before fiducial mark check when
the PCB is loaded.
Recognizes the bad mark in multi array PCB first, and makes skip checking the
fiducial mark of the PCB that does not need to be installed.
However, when the PCB is fixed on the placement position of the conveyor, and setup
position of the bad mark changes due to PCB shape causing confirmation of bad mark
to be done first, then errors can occur as the position of the setup does not match.
In this case, the fiducial mark must be recognized first, and the position of the bad
mark must be compensated accurately.
<Use Manual Fiducial Teach> check box
When placing the parts on the PCB in the Product menu, if the fiducial mark has been
recognized incorrectly, this function is used to solve the problem by displaying the
15-26
Fast Flexible Placer SM481(L) PLUS Administrator’s Guide
Fiducial Mark Dialog Box automatically.
This dialog box does not appear when adjusting the fiducial mark in the Step Dialog
Box, but appears only when placing the part in the Product menu.
If this function is selected, when the fiducial mark recognition fails during part
placement, the message “Do you want to retry after adjusting the fiducial position
again?” appears in the error message window at the bottom of the MMI screen.
However, when this function is not selected, if the fiducial mark recognition fails, this
dialog box does not appear, and only an error message is displayed in the error
message window at the bottom of the MMI screen. This function is selected by
default.
<Use Light Saver function> check box
Used for selecting the function of turning off the lighting of the fiducial camera after
elapse of a certain period of time when the equipment is in idle condition. An edit box
at the right side is activated when this check box is selected. Here, input the waiting
time for the MMI program to turn off the lighting of the camera in idle condition.
<Use Air Saver function> check box
Used for selecting the function of turning off the vacuum after elapse of a certain
period of time when the equipment is in idle condition. An edit box at the right side is
activated when this check box is selected. Here, input the waiting time for the MMI
program to turn off the vacuum in idle condition.
<Use Rank Check> check box
Selecting this check box will create a <Rank> column in the “Feeder Registration”
dialog box. The <Rank> column is used to register and mange the rank of LED parts.
<Show Part Description> check box
The ‘Description’ column is created in the <Feeder> menu.
<Gamma Data Generation> check box
This function is selected when using the gamma interface applied by Samsung
Electronics.
15-27
System Setup
<Buzzer On at error State> combo box
A buzzer sounds when an error occurs during the operation of the equipment. At this
time, selecting the method of the sounding buzzer is possible.
Silence: Do not sound buzzer.
Always: Always sound buzzer.
Machine: Able to setup the buzzer sound differently according to the status of
warning error.
<Tray Pallet Change Speed> combo box
When installation of parts is performed with many pallets in fast (fastest) speed, make
the next pallet standby at working position unless vision fail occurs after picking up a
part in a pallet. From the equipment which it sees it is a function which it does not
support.
<Tape Auto Link Disable> check box
When this item is selected, the auto link function is not used for the tape feeder.
<Stick Auto Link Disable> check box
When this item is selected, the auto link function is not used for the stick feeder.
<Both front and rear Feeder base> check box
This machine provides the Link function so that if the parts of the tape feeder mounted
in the feeder base run short, it searches another tape feeder by feeding the part
identical to the part that was used up and allowing the parts of this tape feeder to be
placed.
When searching the tape feeder, the one installed in the front feeder base is searched
first. If there is no corresponding tape feeder in the front side feeder base, it searches
the tape feeder installed in the feeder base in the rear side.
The default setup allows only the front side feeder base to be used. However, if this
Link function is selected, it can use both the front and rear side feeder bases.
<NCS> button
Used to change a job without stopping the machine. For more details regarding this,
contact us.
<Transporter> button
In the in-line system composed of several machines, this function allows reduction of
the time taken for the next machine to recognize the board information recognized and
transmitted by the previous machine, from the first to the last machine.