DECAN_F2_Service(Eng_Ver1).pdf - 第415页
17-3 Troubleshooting 17.3. Process Trouble Shooting 17.3.1. PC Boot ing Failure E0500 turning on the power supply, a ‘No Signal’ message appe ars on the monitor [Cause] The input voltage (220V) and output voltage (5V ,…
17-2
Fast & Flexible Chip Shooter DECAN F2 Service Manual
17.2. Necessary Data according to Problems
When the following problems occur, transmit the corresponding file.
8 All Files in D:\ErrVisFile
Folder
In case of a problem related to the vision
recognition, this file is necessary
additionally.
9 RT Telemetry File When the machine operates abnormally
during production and operation, this file
is necessary to analyze the problem.
10 Vision Error Image File Used to check any problem with the
recognition result.
11 Screen Capture File When an error message related to a
window occurs or an error occurs during
MMI screen manipulation, this file is
necessary to check the problem.
NO Necessary File Data Description
1 PCB, LOG, SYSTEM,
SMBACKUP, Screen
Capture, etc.
When an error occurred during MMI
programming or in use
2 PCB, LOG, SYSTEM,
RT Telemetry, etc.
When the machine exhibits a problem
during operation or production
3 PCB, LOG, SYSTEM,
PDInfo, Vision Error
Image, ErrVisFile, etc.
When the part dump rate increases and
a vision error occurs
4 PCB, LOG, SYSTEM,
TEMP, etc
When an error occurs before and after
the optimizer
17-3
Troubleshooting
17.3. Process Trouble Shooting
17.3.1. PC Booting Failure
E0500 turning on the power supply, a ‘No Signal’ message appears on the monitor
[Cause]
The input voltage (220V) and output voltage (5V, 12V) of the PC power supply have a
problem
The HDD was damaged due to frequent booting error and failure
The SBC board and CPU are defective (a beep sound occurs)
The board operates abnormally due to an increase in the internal temperature of the PC
rack
The back plane is defective (no beep sound)
Defective vision board and MMI board (Defective RS232 port)
Complex defects : Defective SBC board and back plane board, defective CPU, virus
infection, CUP temperature increase, etc.
Unstable main power supply
The CPU is overheated due to a defective CPU cooling fan
The monitor is defective or the signal cable is not connected
[How to Check]
Check whether the cooling fan on the Control rack operates properly when turning on
the power. If the fan does not operate, check whether the input voltage (220V) and
output voltage (5V, 12V) of the PC power supply are normal Check the input end
voltage (+12V) of the external power supply of the vision board.
Check whether the HDD is properly recognized in the CMOS Setup
Check whether the priority of the HDD is 1 in the MMI SBC CMOS boot sequence.
Perform the CMOS reset test and check whether the message ‘CMOS was set with the
default value’ is displayed on the screen
Check whether the temperature at the site is higher than 24ºC
Cause Description Remarks
Defective part Turning on the power supply will display ‘No Signal’ on the
monitor.
E0500
Blue screen occurs while booting or running the PC. E0501
The PC stops when it almost starts Windows while booting
the PC
E0502
17-4
Fast & Flexible Chip Shooter DECAN F2 Service Manual
Check the status of the back plane. Check for any defective pins (check whether a bent
pin exists). Replace the SBC board and back plane board and check whether they are
booted properly
Check whether the CMOS Setup screen is displayed.
Check whether the RT, MMI, ZMP(Motion Control) board, back plane board, CPU,
HDD and cooling fan have a problem
Check whether the main voltage is applied properly
Check whether the CPU cooling fan operates properly
Check whether the monitor power supply and signal cable are connected properly. If
not, replace the monitor and check whether the screen is displayed properly
[Measures]
If the input and output of the PC power supply are abnormal, replace it.
Replace and recover the HDD and then reinstall the MMI.
Replace the SBC board.
Remove the dummy slot cover and discharge the heat inside the PC rack and then
reboot the PC.place the SBC board and CPU.
Replace the RT board and Back plane board.
Replace the HDD or MMI board and perform HDD recovery.
For items with a problem, refer to the above measures and apply grease between the
CPU and CPU cooling fan. (The CPU temperature is reduced by approximately 20ºC.)
When the input power supply is unstable, propose the UPS installation.
Replace the CPU cooling fan.
Connect the power supply cable connected to the monitor and the signal cable again. f
the same problem occurs, replace the monitor or the signal cable.
E0501 Blue screen occurs while booting or running the PC
[Cause]
HDD and Windows system file were damaged
The Windows system file was infected by a virus
Booting speed becomes slower or booting failure occurs frequently.
Defective SBC board
Defective SBC board and HDD
Defective SBC board and CPU
Defective vision board and COM-VM sub-board
The SBC board is not inserted into the vision board connector properly
The temperature inside the PC has increased or the HDD rack case contact is defective