DECAN_F2_Service(Eng_Ver1).pdf - 第437页

17-25 Troubleshooting [Measures]  Set the part dump angle to 90º E071E The report is not outputted from the ‘Feeder Info.’ dialog box of the Utility menu [Cause]  The printer is not set in the machine PC [How to Check]…

100%1 / 604
17-24
Fast & Flexible Chip Shooter DECAN F2 Service Manual
[Measures]
Perform HDD recovery and install the operating system and MMI.
E071A An error indicating the skip count occurred in the Steps dialog box
[Cause]
The filtering function is used in the ‘Step’ dialog box
[How to Check]
Check whether the filtering function is applied in the ‘Step’ dialog box
[Measures]
Release the filtering function and check the skipped part.
E071B Failed to pick up 0603 chips simultaneously
[Cause]
The feeder position is not set correctly or the System Factory Constant is set
incorrectly.
[How to Check]
After checking whether the feeder position is set correctly, check whether the No. 73
item of the System Factory Constants is ‘250’.
[Measures]
Modify the factory constant for the simultaneous pickup of 0603 chips. (No. 73 VERY
SMALL COMPSIZE: 380 250)
E071C Head# Dump Limit Error
[Cause]
The dump box position is set to the position where all heads cannot access
[How to Check]
Check the dump box position setup of the system to check whether it is at a position
where all heads can access it
[Measures]
Add and use new dump box at a position where all heads can access it.
E071D An error occurred while dumping the connector
[Cause]
The connector length is longer than the dump box width
[How to Check]
Check whether the part dump angle is correct and check that the dump box width is
longer than the connector length
17-25
Troubleshooting
[Measures]
Set the part dump angle to 90º
E071E The report is not outputted from the ‘Feeder Info.’ dialog box of the Utility menu
[Cause]
The printer is not set in the machine PC
[How to Check]
Check whether the printer is properly set in the PC
[Measures]
Install the printer driver so that the machine PC can use the printer.
E071F The machine pauses with the machine being changed into the 'Run-Ready' state
during
[Cause]
Defective RT and NCIO boards
[How to Check]
Check whether the same problem occurs while replacing the RT board and NCIO
board in order
[Measures]
Replace the RT board or NCIO board.
E0720 The machine pauses during production
[Cause]
The 'Coil Check' function is set for the Chip-Rect part
[How to Check]
Check whether the Chip-Rect part is properly set in the part editor
[Measures]
Disable the 'Coil Check' function for the Chip-Rect part.
E0721 Limitation occurred when exchanging a PCB file between machines
[Cause]
The stopper position of the machine is different from that of the PCB program file
copied from another machine
[How to Check]
Check whether the stopper position of the machine to be used is the same as the
stopper position of the machine from which the file has been copied
[Measures]
17-26
Fast & Flexible Chip Shooter DECAN F2 Service Manual
Set the PCB stop position the same as that of the existing machine and move the
stopper.
E0722 Timeout occurred during Msgdriver (MMI) communication
[Cause]
Defective Vision board
Defective LAN communication
[How to Check]
Replace the Vision board and check whether the same problem occurs
Check whether the Ethernet communication is properly made
[Measures]
Replace the PCI I/O board.
Connect the LAN cable properly or replace the cable.
E0723 A certain part is dumped even when a pickup error did not occur
[Cause]
Incorrect system constant setup
[How to Check]
Check the retry count of the pickup from the Common Data in the part editor and
check that the No. 9 System Constant is 5
[Measures]
Change the system constant. (No. 9: Change the OPT SIG PART EMPTY from 7 to 5.)
E0724 Timeout occurred during Msgdriver (MMI) communication (Applicable only to SM
series machines excluding the SM471 machines.)
[Cause]
The PCI IO board is defective. (Applicable only to SM series machines excluding the
DECAN F2, SLM, SM471 and SM48X.)
The cable connecting the CAN Master board and PCI I/O board is defective.
(Applicable only to SM series machines excluding the DECAN F2, SLM, SM471 and
SM48X.)
[How to Check]
Replace the PCI I/O board and check whether the same problem occurs.
Check whether the DPRAM cable is correctly connected. If its connection has no
problems, replace the cable and check whether the same problem occurs.
[Measures]
Replace the PCI I/O board.