DECAN_F2_Service(Eng_Ver1).pdf - 第428页

17-16 Fast & Flexible Chip Shooter DECAN F2 Service Manual E0701 Ram Ring Error [Cause]  The cable connecting the PCI I/O board and DPRAM is defective (Applicable only to SM series machines excluding the DECAN F2, S…

17-15

Troubleshooting

E0700 Pause while downloading the MMI

[Cause]

 The system file was damaged after being infected by a virus

 The SBC board is not properly connected to the vision board connector or the vision

board is not properly inserted into the back plane slot (defective SBC board contact)

 The NCIO board is not properly inserted into the back plane board slot

 A problem occurred with MMI booting due to a damaged MMI system file

 The SBC board, CPU, HDD, etc. are comprehensively defective

 The RT and NCIO boards are not properly inserted into the back plane board slot

 Defective CPU of the SBC board

[How to Check]

 Perform a virus check of the HDD. If it has a problem, perform HDD recovery and

reinstall the MMI. Then check whether the same problem occurs

 Remove the SBC board from the back plane board slot. Then insert it properly and

check whether the same problem occurs

 Remove the SBC board from the vision board connector and insert it again. Then

remove the vision board from the back plane board slot and insert it again properly and

then check whether the same problem occurs continuously

 Check whether the NCIO board is properly inserted into the back plane board slot

 Reinstall the MMI and check whether the same problem occurs

 Replace the SBC board, CPU and HDD in order and check whether the same problem

occurs to them

 Check whether the RT and NCIO boards are properly inserted into the back plane

board slot

 Replace the CPU and check whether the same problem occurs

[Measures]

 Perform HDD recovery and reinstall the MMI.

 Remove the SBC board from the vision board connector and insert it again. Then

remove the vision board from the back plane board slot and insert it again properly.

 Insert the NCIO board into the back plane board slot properly.

 Reinstall the MMI.

 Replace the SBC board, CPU and HDD in order. If the HDD has a problem, perform

HDD recovery after replacing it and reinstall the MMI.

 Insert the RT and NCIO boards into the back plane board slots properly.

 Replace the CPU.

17-16

Fast & Flexible Chip Shooter DECAN F2 Service Manual

E0701 Ram Ring Error

[Cause]

 The cable connecting the PCI I/O board and DPRAM is defective

(Applicable only to SM series machines excluding the DECAN F2, SLM, SM471 and

SM48X.)

 A communication error occurred between the CAN Master and the PCI I/O board.

(Applicable only to SM series machines excluding the DECAN F2, SLM, SM471 and

SM48X.)

 The PCI I/O board is defective.

(Applicable only to SM series machines excluding the DECAN F2, SLM, SM471 and

SM48X.)

 The CAN Master board and MVME 3100 board are defective.

(Applicable only to SM series machines excluding the DECAN F2, SLM, SM471 and

SM48X.)

 The Vision board is not inserted into a slot correctly.

(Applicable only to SM series machines excluding SLM471)

[How to Check]

 Check whether the cable that connects the PCI I/O board and the DPRAM is correctly

connected.

 Remove the PCI I/O board and CAN Master board from the slots and insert them

again and then check whether the same problem occurs.

 Replace the PCI I/O board and check whether the same problem occurs.

 Replace the CAN Master board and MVME 3100 board and check whether the same

problem occurs.

 Remove the Vision board from the slot and insert it into the slot again and then check

whether the same problem occurs.

[Measures]

 Check the connection status of the corresponding cable and if there are any problems,

replace the cable connecting the PCI I/O board and DPRAM.

 Remove the PCI I/O board and CAN Master board from the slots and insert them

correctly.

 Replace the PCI I/O board.

 Replace the CAN Master board and MVME 3100 board.

 Remove the Vision board from the slot and insert it correctly.

17-17

Troubleshooting

E0702 The Assert error occurred while loading the PCB program

[Cause]

 Optimizer feeder base setup error

[How to Check]

 When running the optimizer, check error messages as well as the setups for the

optimizer.

[Measures]

 Educate users regarding how to use the optimizer.

E0703 Assert[O] error occurred (File. Common.MmiRT Comm. DPRAM -.Struct.h Line

145)

[Cause]

 The system file was damaged after being infected by a virus

[How to Check]

 Perform HDD recovery and reinstall the MMI. Then check whether the same problem

occurs

[Measures]

 Perform HDD recovery and reinstall the MMI.

E0704 The monitor image is turned off intermittently and discolored, and the screen vibrates

[Cause]

 The cable connecting the vision board (VGA connector) is not properly connected

 Incorrect touch panel setup

 Defective touch panel

[How to Check]

 Check whether the cable connecting the vision board (VGA connector) and touch

panel is properly connected. If it has a problem, replace the cable and check whether

the same problem occurs

 Check whether the touch panel color is correct

 Replace the touch panel and check whether the same problem occurs

[Measures]

 Replace the cable connecting the vision board (VGA connector) and touch panel.

 Execute the function to adjust the touch panel color automatically.

 Replace the touch panel.