DECAN_F2_Service(Eng_Ver1).pdf - 第418页

17-6 Fast & Flexible Chip Shooter DECAN F2 Service Manual  Perform HDD recovery and reinstall the MMI.  Replace and rec over the HDD and then reinstall the MMI.  Remove the memory of the SBC bo ard and insert it a…

17-5

Troubleshooting

[How to Check]

 Check the Windows error information and check whether a bad sector occurred to the

HDD

 Check for virus infection using an anti-virus program

 Replace the SBC board and check whether the PC is booted properly

 Access the CMOS Setup screen to check whether the HDD is recognized properly

 Replace the SBC board and CPU to check whether the PC is booted properly

 Replace the vision board and COM-VM sub-board and check whether they are booted

properly

 Check whether the SBC board is inserted into the vision board connector properly

 Check whether the site temperature is higher than 24? and then check whether the

HDD is recognized properly

[Measures]

 Replace and recover the HDD and then reinstall the MMI.

 Perform virus treatment and install HDD Recovery software.

 Replace the SBC board.

 Replace the SBC board and HDD, perform HDD recovery and reinstall the MMI.

 Replace the SBC board.

 Replace the vision board or COM-VM sub-board.

 Remove the SBC board and insert it into the vision board connector properly.

 Remove the slot cover and discharge the heat inside the PC rack and then reboot the

PC.

E0502 The PC stops when it almost starts Windows while booting the PC

[Cause]

 The ‘Initializing and establishing link …’ error occurred in the DOS mode

 Defective HDD

 The memory of the SBC board is not inserted properly

 Defective SBC board

[How to Check]

 Check for the occurrence of the ‘Initializing and establishing link’ error

 Access the CMOS Setup screen to check whether the HDD is recognized properly

 Check whether the memory of the SBC board is inserted properly

 Replace the SBC board and check whether the PC is booted properly

[Measures]

17-6

Fast & Flexible Chip Shooter DECAN F2 Service Manual

 Perform HDD recovery and reinstall the MMI.

 Replace and recover the HDD and then reinstall the MMI.

 Remove the memory of the SBC board and insert it again properly.

 Replace the SBC board.

17.3.2. Failed to initialize the MMI and unable to execute it

E0600 The [Grabber type does not match...], [fail to run visframe] and [Run Time Error]

error occurred during VisFrame initialization while loading the MMI.

[Cause]

 Defective SBC board

 The vision image file is infected by a virus

 When the control rack contact is defective (SBC, Vision, RT CPU, NCIO, ZMP) /

SBC board is not connected to the vision board connector / Vision board, RT board

and ZMP board are not inserted into the back plane slot properly

 The MMI file is damaged

 The back plane board is not properly inserted into the board

 The VisFrame initialization failed since the time at which the vision error occurred is

different from the Windows XP time due to defective Windows XP time setup

 The vision board, RT board, NCIO board and ZMP board are not recognized due to a

defective back plane board

Cause Description Remarks

Defective

initialization

The [Grabber type does not match...], [fail to run visframe]

and [Run Time Error] error occurred to the Initializing

visframe while loading the MMI

E0600

The MMI does not operate and the PC has been shut down

(occurred during MMI operation)

E0601

When booting the PC after shutdown, it is repeatedly

rebooted

E0602

The processing speed of the PC is slow with a pause during

processing

E0603

An Initializing Machine I/F error occurred while loading the

MMI

E0604

An MFC related arithmetic operation error occurred while

booting the MMI (system file not found)

E0605

Defective MMI booting (assert failure occurred) E0606

A Windows system error occurred while loading the MMI

(forced exit)

E0607

17-7

Troubleshooting

 Defective NCIO board (only for the Excen machine)

 Defective base control board (only for the Excen machine)

[How to Check]

 Replace the SBC board and check whether the MMI is properly executed

 Check whether the image in the ErrorVisFile of the D drive has no problem

 After checking whether the SBC board is properly connected to the vision board

connector, check whether the vision board, RT board, NCIO board and ZMP board are

properly inserted into the back plane slot

 Reinstall the MMI and check whether the same problem occurs

 Check whether the Windows XP time setup is correct

 Replace the back plane board and check whether the MMI is properly executed

 Replace the NCIO master board and check whether the MMI is properly executed

 Replace the Base Control board and check whether the MMI is properly executed

[Measures]

 Replace the SBC board.

 Delete the image on which the saving date is not indicated and perform a virus check

periodically.

 Check whether the CPU module is properly inserted into the SBC board; whether the

SBC board is properly connected to the vision board connector; and whether the vision

board, RT board, NCIO board and ZMP board are properly inserted into the back

plane board.

 Reinstall the MMI.

 Check whether a back plane pin is bent and insert the vision, RT, NCIO and ZMP

boards properly again.

 Change the Windows O/S or delete the folder in which vision error images are saved.

 Replace the back plane.

 Replace the NCIO master board.

 Replace the Base Control board.

E0601 The MMI does not operate and the PC has been shut down (occurred during MMI

operation)

[Cause]

 The program runs slowly and the PC is shut down due to an overheated CPU as the PC

rack cooling fan does not operate

 Defective SBC board

 The Windows system file is damaged