DECAN_F2_Service(Eng_Ver1).pdf - 第417页

17-5 Troubleshooting [How to Check]  Check the W indows error information and ch eck whether a bad sector occurred to the HDD  Check for virus infection us ing an anti-virus program  Replace the SBC board and check wh…

17-4

Fast & Flexible Chip Shooter DECAN F2 Service Manual

 Check the status of the back plane. Check for any defective pins (check whether a bent

pin exists). Replace the SBC board and back plane board and check whether they are

booted properly

 Check whether the CMOS Setup screen is displayed.

 Check whether the RT, MMI, ZMP(Motion Control) board, back plane board, CPU,

HDD and cooling fan have a problem

 Check whether the main voltage is applied properly

 Check whether the CPU cooling fan operates properly

 Check whether the monitor power supply and signal cable are connected properly. If

not, replace the monitor and check whether the screen is displayed properly

[Measures]

 If the input and output of the PC power supply are abnormal, replace it.

 Replace and recover the HDD and then reinstall the MMI.

 Replace the SBC board.

 Remove the dummy slot cover and discharge the heat inside the PC rack and then

reboot the PC.place the SBC board and CPU.

 Replace the RT board and Back plane board.

 Replace the HDD or MMI board and perform HDD recovery.

 For items with a problem, refer to the above measures and apply grease between the

CPU and CPU cooling fan. (The CPU temperature is reduced by approximately 20ºC.)

 When the input power supply is unstable, propose the UPS installation.

 Replace the CPU cooling fan.

 Connect the power supply cable connected to the monitor and the signal cable again. f

the same problem occurs, replace the monitor or the signal cable.

E0501 Blue screen occurs while booting or running the PC

[Cause]

 HDD and Windows system file were damaged

 The Windows system file was infected by a virus

Booting speed becomes slower or booting failure occurs frequently.

 Defective SBC board

 Defective SBC board and HDD

 Defective SBC board and CPU

 Defective vision board and COM-VM sub-board

 The SBC board is not inserted into the vision board connector properly

 The temperature inside the PC has increased or the HDD rack case contact is defective

17-5

Troubleshooting

[How to Check]

 Check the Windows error information and check whether a bad sector occurred to the

HDD

 Check for virus infection using an anti-virus program

 Replace the SBC board and check whether the PC is booted properly

 Access the CMOS Setup screen to check whether the HDD is recognized properly

 Replace the SBC board and CPU to check whether the PC is booted properly

 Replace the vision board and COM-VM sub-board and check whether they are booted

properly

 Check whether the SBC board is inserted into the vision board connector properly

 Check whether the site temperature is higher than 24? and then check whether the

HDD is recognized properly

[Measures]

 Replace and recover the HDD and then reinstall the MMI.

 Perform virus treatment and install HDD Recovery software.

 Replace the SBC board.

 Replace the SBC board and HDD, perform HDD recovery and reinstall the MMI.

 Replace the SBC board.

 Replace the vision board or COM-VM sub-board.

 Remove the SBC board and insert it into the vision board connector properly.

 Remove the slot cover and discharge the heat inside the PC rack and then reboot the

PC.

E0502 The PC stops when it almost starts Windows while booting the PC

[Cause]

 The ‘Initializing and establishing link …’ error occurred in the DOS mode

 Defective HDD

 The memory of the SBC board is not inserted properly

 Defective SBC board

[How to Check]

 Check for the occurrence of the ‘Initializing and establishing link’ error

 Access the CMOS Setup screen to check whether the HDD is recognized properly

 Check whether the memory of the SBC board is inserted properly

 Replace the SBC board and check whether the PC is booted properly

[Measures]

17-6

Fast & Flexible Chip Shooter DECAN F2 Service Manual

 Perform HDD recovery and reinstall the MMI.

 Replace and recover the HDD and then reinstall the MMI.

 Remove the memory of the SBC board and insert it again properly.

 Replace the SBC board.

17.3.2. Failed to initialize the MMI and unable to execute it

E0600 The [Grabber type does not match...], [fail to run visframe] and [Run Time Error]

error occurred during VisFrame initialization while loading the MMI.

[Cause]

 Defective SBC board

 The vision image file is infected by a virus

 When the control rack contact is defective (SBC, Vision, RT CPU, NCIO, ZMP) /

SBC board is not connected to the vision board connector / Vision board, RT board

and ZMP board are not inserted into the back plane slot properly

 The MMI file is damaged

 The back plane board is not properly inserted into the board

 The VisFrame initialization failed since the time at which the vision error occurred is

different from the Windows XP time due to defective Windows XP time setup

 The vision board, RT board, NCIO board and ZMP board are not recognized due to a

defective back plane board

Cause Description Remarks

Defective

initialization

The [Grabber type does not match...], [fail to run visframe]

and [Run Time Error] error occurred to the Initializing

visframe while loading the MMI

E0600

The MMI does not operate and the PC has been shut down

(occurred during MMI operation)

E0601

When booting the PC after shutdown, it is repeatedly

rebooted

E0602

The processing speed of the PC is slow with a pause during

processing

E0603

An Initializing Machine I/F error occurred while loading the

MMI

E0604

An MFC related arithmetic operation error occurred while

booting the MMI (system file not found)

E0605

Defective MMI booting (assert failure occurred) E0606

A Windows system error occurred while loading the MMI

(forced exit)

E0607