DECAN_F2_Service(Eng_Ver1).pdf - 第456页
17-44 Fast & Flexible Chip Shooter DECAN F2 Service Manual 17.3.7. Even though the Ready On button is pressed, power is not supplied to the servo motor (E0B) Cause Description Remarks Even though the Ready On button …
17-43
Troubleshooting
E0A07 [EMER] Axis # motor or origin position has been changed
[Cause]
Defective Connector Pin assembling
Motor origin position has been changed (environmental change)
Defective Z-axis motor
[How to Check]
1. Check the assembling state of the corresponding axis connector.
2. Check the motor origin and Z offset.
3. Check the motor operation state of the corresponding axis.
[Measures]
Reassemble the pin to the connector of the Z-axis board.
Calibrate the axis.
Replace the Z-axis and calibrate it.
E0A08 The Head $H picked the part $P at its edge in the feeder $F
[Cause]
A problem occurred to the system data [Calibration Data].
[How to Check]
Check the bending state of the Head Ball Spline.
[Measures]
Calibrate the head.
E0A09 Axis $A home calibration is not calibrated
[Cause]
Origin has been changed.
[How to Check]
Check the Z# home calibration.
[Measures]
Perform the Z# home calibration.
17-44
Fast & Flexible Chip Shooter DECAN F2 Service Manual
17.3.7. Even though the Ready On button is pressed, power is not supplied to the servo
motor
(E0B)
Cause Description Remarks
Even though the
Ready On
button is
pressed, power
is not supplied
to the servo
motor
Defective emergency switch connection E0B00
Infected by a virus E0B01
Defective PCI I/O Board contact
(Applicable only to SM series machines excluding the
DECAN F2, SLM, SM471 and SM48X.)
E0B02
Defective CAN Conveyor Board E0B03
Defective Safety Override Key contact E0B04
Defective relay contact of the Safety Control Board E0B05
Defective Step Driver E0B06
Defective CAN Master Board
(In the case of DECAN F2, SLM, SM471 and SM48X
machines, the Axis I/O Board is defective.)
E0B07
Defective contact of the PCI IO Board and Can Master Board
(Applicable only to SM series machines excluding the
DECAN F2, SLM, SM471 and SM48X.)
E0B08
Defective Magnetic Contactor E0B09
Defective SEDES Board
(Applicable only to SM series machines excluding the
DECAN F2, SLM, SM471 and SM48X.)
E0B0A
Servo motor
unable to
operate
Defective servo motor or servo motor drive E0B0B
Defective servo motor
Overload The motor is overloaded E0B0C
Under voltage,
over voltage
Check the drive and power supply line E0B0D
The machine
power supply
has no problem
but power is not
supplied to the
motor drive
The machine power supply has no problems but the power is
not supplied to the motor drive
E0B0E
Vibration and
resonance
A Vibration or resonance occurs to a specific axis motor E0B0D
Encoder related
alarm occurred
An Encoder related alarm occurred E0B10
Overvoltage
related alarm
Voltage is high E0B11
17-45
Troubleshooting
E0B00 Defective emergency switch connection
[Cause]
Defective emergency switch contact
[How to Check]
Check the connection status of the emergency switch cable and check the operation
status of the emergency switch contact
[Measures]
Reassemble the emergency switch.
Replace the safety control board.
E0B01 Infected by a virus
[Cause]
Infected by a virus
[How to Check]
Perform a virus check using an anti-virus program
[Measures]
Treat it with an anti-virus program, or if it is not possible to treat it, perform HDD
recovery and reinstall the MMI.
E0B02 The NCIO board is not properly inserted into the back plane board slot
[Cause]
The NCIO board is not properly inserted into the back plane board slot
[How to Check]
Check whether the NCIO board is properly inserted into the back plane board slot
[Measures]
Insert the NCIO board into the back plane board slot properly.
E0B03 Defective PCI I/O Board contact
[Cause]
Defective PCI I/O Board contact
[How to Check]
1. Check the PCI Board assembling and operation state.
Undervoltage
related alarm
Voltage is low E0B12
Cause Description Remarks