RS-1_instruction manual.pdf - 第199页
Part 1 B asic O peration Chapter 2 Pr oduction 2- 88 No. Displayed er ror me ssage 91 MT C COMM ERR (Power Off) 92 Step Number of T ray is Wr ong 93 MTC is not Ava ilable in Setup Data 94 Not Findin g STX ETX 95 Undefine…
Part 1 Basic Operation Chapter 2 Production
2-87
No.
Displayed error message
45 No.2 Head error
46 Over Run Shuttle
47 Y Holder Error
48 Not finish initialize
49 Mounter emergency stop
50 Over run error(Z - limit)
51 Over run error(X - limit)
52 Over run error(Y - limit)
53 No.1 Head Sensor error
54 Over run error( Shuttle )
55 Interlock error
56 Z error
57 X error
58 Y error
59 No.2 Head Sensor error
60 Shuttle error
61 Door,Cover SW error
62 Overrun error
63 Z axis sensor error
64 X axis sensor error
65 Y axis sensor error
66 RAM error
67 Illegal break current
68 Holder Sensor error
69 Motor Off
70 Sensor error(Z + limit)
71 Sensor error(X + limit)
72 Sensor error(Y + limit)
73 Shuttle sensor error
74 NV-RAM error
75 Close/open sensor error
76 Impossible servo driver on (Z)
77 Soft Limit (Shuttle)
78 Servo alarm
79 Bulb bad motion
80 Request cancell
81 Switch Off-line
82 Switch Supply
83 Press MTC EMG Sw
84 Retry Out
85 Empty Parts
86 Supply
87 MTC COMM ERR (Data Error)
88 MTC COMM ERR (Communication Error)
89 MTC COMM ERR (Procedure Error)
90 MTC COMM ERR (Synchronous Error)
Part 1 Basic Operation Chapter 2 Production
2-88
No.
Displayed error message
91 MTC COMM ERR (Power Off)
92 Step Number of Tray is Wrong
93 MTC is not Available in Setup Data
94 Not Finding STX ETX
95 Undefined Command Code is Specified
96 Parts Request Send Multiplexy (WAIT)
97 Parts Request Send Multiplexy (KICK)
98 Parts Request is Abnormal
99 Response Time Out
100 MTC Initialize Incompletely
101 Unmovable by Off-line
102 Unmovable by Air-Down
103 IPC Object Close Error (MTC－1)
104 IPC Object Close Error (MTC－2)
105 IPC Object Close Error (MTS－1)
106 IPC Object Close Error (MTS－2)
107 IPC Object Close Error (DTS－1)
108 IPC Object Close Error (DTS－2)
109 IPC Object Close Error (MTC－1)
110 Move error
111 Retry over
112 No component
113 Offline
114 Supply
115 Pick miss
116 Time Out (Ready Waiting Observation 10sec)
117 Time Out (Sync Character Observation 4sec)
118 Time Out (ETX Observation 3sec)
119 MTC Power Off
120 Time Out (Responseless Observation 60sec)
121 Receive Data Validity Error
122 Ring Buffer Access Error
123 Time Out (Data Link Release 1)
124 Time Out (Data Link Release 2)
125 MTC Communication Initialize Failed
Part 1 Basic Operation Chapter 2 Production
2-89
10) Error (Detail – Coplanarity)
No.
Displayed error message
1 A coplanarity judgemennt error.
2 A coplanarity centering position error.
3 A lead count error.
4 A colinearity judgemennt error.
5 A coplanarity unit error.
6 A illegal data or illegal operation.
7 A coplanarity adjust error.
8 A time-out or other error.
9 A hardware error of coplanarity controler.
10 A measurement software error.
11 A lasor diode is abnormal.
12 A cable connection error.
13 The motor revolution is abnormal.
14 A memory of sencer is abnormal.
15 A initialize error of coplanarity unit.
16 An axis error of coplanarity measurement.
17 The component type can not be measured.
18 The component size is too large.
19 The component size is out of range.
20 The component height is too high.
21 The meas. mode isn't corr. or the compo. cann't be measured.
22 The electrode can not be measured.
23 A coplanarity sensor is unused.