RS-1_instruction manual.pdf - 第25页
Part 1 B asic O peration Chapter 1 Overv iew of the Machine 1-7 Other supplied d evices IC collect ion belt △ Linear type t ranscription unit (To be instal led on the main u nit / front or rear) － Linear type trans cript…
Part 1 Basic Operation Chapter 1 Overview of the Machine
1-6
Equipment
Feeder float sensor
○
Automatic Tool Change unit (ATC)
○
Support of a large-sized nozzle (ATC)
△
Only for an RS-1R
Nozzle RFID
△
Only for an RS-1R
Large-sized component trash box
－
Flexible Calibration System (FCS)
○
FCS adjustment jig
△
SOT direction inspection table
－
Component Verification System (CVS)
△
Coplanarity
△
Low load control
△
High load control
－
Offset Placement After Solder Screen-printing
△
Tape setting unit (front)
○
A counter measure will be taken in and after Rev.D,
Tape setting unit (rear) △
A counter measure will be taken in and after Rev.D. This unit
cannot be used together with a TR-5D.
Production support system
Component database
○
Separate PC is required.
External Programming Unit (EPU)
－
Floor productivity improvement
support system
IS
－
IS Lite
－
IFS-NX
△
JaNets
△
White list type anti-virus software
○
Component supply device
Feeder bank for supporting an electric tape feeder
Fixed type (Front)
△
Factory-set option
Fixed type (Rear)
△
Factory-set option ("None" acceptable)
Designed for a feeder exchange trolley
Feeder exchange trolley (RF/EF)
△
Factory-set option
Feeder exchange trolley (RF)
△
Factory-set option
Remaining tape disposition
Tape cutter
○
Trash box
△
Component supply unit
EF series electric feeder △
When you attach an RF_ETF _Attachment on the RF/EF
bank, an EF series electric feeder can be attached on the
bank. (When you use this RF_ETF_Attachment,
non-teaching is not supported and the simultaneous
component pick-up is not guaranteed.) Note that an
EF08HDR is not included as an available feeder, and that an
EF72FS and an EF88FS can be provided as a customized
product respectively.
RF series electric feeder
△
EF series electric Stick feeder △
When you attach an RF_ETF_Attachment on the RF/EF
bank, an EF series electric Stick feeder can be attached on
the bank. (When you use this RF_ETF_Attachment,
non-teaching is not supported and the simultaneous
component pick-up is not guaranteed.)
Only feeders whose revision is C or later are supported.
Tray supply unit
TR8SR (MTS)
△
TR7D
－
TR5SNX
△
Supported in Rev. G or later
TR5DNX
△
Supported in Rev. G or later
TR6SNV
△
Supported in Rev. D or later
TR6DNV
△
Supported in Rev. E or later
TR6SXLX
△
Supported in Rev. D or later Only for RS-1XL
TR6DXLX
△
Supported in Rev. E or later Only for RS-1XL
TR1RB
△
Tray holder
△
Two types of full type and half type
Part 1 Basic Operation Chapter 1 Overview of the Machine
1-7
Other supplied devices
IC collection belt
△
Linear type transcription unit
(To be installed on the main unit / front or rear)
－
Linear type transcription unit
(To be attached on an electric bank/front or rear)
－
Rotary type transcription unit
(To be attached on a bank/front or rear)
－
Feeder setup stand for electric feeder (EF)
△
Feeder setup stand for electric feeder (RF)
△
RF_ETF_Attachment,
△
Descriptions of the abbreviations used in this Manual
Abbreviation Meaning
ATC
(Auto Tool Changer)
CVS
(Component Verification System)
DTS
(Dual Tray Server)
ETF
(Electric Tape Feeder)
HMS (Height Measurement System)
IFS-NX
(Intelligent Feeder System)
LNC
(Laser align New Concept)
MTC
(Matrix Tray Changer)
MTS
(Matrix Tray Server)
OCC
(Offset Correction Camera)
PWB
(Printed Wiring Board)
S-VCS
(Scanning Vision Centering System)
VCS
(Vision Centering System)
Part 1 Basic Operation Chapter 1 Overview of the Machine
1-8
①
②
⑦
③
⑤
⑧
⑥
④
⑤
⑨
⑫
⑩
⑪
⑩
Configuration of the machine
① Front liquid crystal monitor ⑤ Mini signal light (option) ⑨ Rear liquid crystal monitor
② Operation panel ⑥ Air regulator (Under the cover)
⑩
Front tape setting unit
* In and after Rev. D
③ Power switch
⑦
Vacuum pump
(Right side inside the machine)
⑪
Rear tape setting unit (Option)
* In and after Rev. D
④ Signal light
⑧
Breaker
(On the right side of the rear)
⑫ Keyboard (option)
①
ATC unit
⑤
PWB transport unit
⑨
CAL block unit
⑬
Load control unit (option)
②
LNC120 head unit
⑥
VCS unit
⑩
Feeder bank unit
⑭ Coplanarity unit (option)
③
Head unit
8-head
⑦ X-Y unit ⑪ HMS unit
⑮
NozzleRFID reader
(option)
④
OCC unit (L)
⑧
CVS unit (option)
⑫
Trash box
③
①
②
⑥
⑦
⑨
④
⑩
⑪
⑫
⑬
⑤
⑧
⑭
⑮