RS-1_instruction manual.pdf - 第934页

Part 2 D etaile d Descript ion of E ach Functi on Chapter 12 Handling th e Optional Device s 12 - 50 (3) Connect each c able and an air tube to t he “MT C power co nnector 1,” the “sig nal connect or 2” and the “air joi …

Part 2 Detailed Description of Each Function Chapter 12 Handling the Optional Devices

12-49

12.8 How to Install a Matrix Tray Changer (MTC)

For this machine, the MTS is selectable from between the TR6SNV and the TR6DNV.

Refer to the MTC Instruction Manual for details on handling and setting.

To install onto an RS-1/1R a TR6SNV or a TR6DNV that was installed on another machine model,

it has to be remodeled, its software has to be upgraded, and the setting of the DIP switch has to be

changed. If any of this is not performed, the system stops urgently when you turn it on.

Contact our Service department for remodeling or upgrading of the MTC.

* To use a TR6SNX or TR6DNX that has been remodeled already and whose software has been

upgraded with an RS-1/1R or another machine model, follow the instructions described in

Sections 12.7.2.

To avoid any accident caused by sudden activation of the machine,

turn off the power.

12.8.1 How to install an MTC

(1) Move the “MTC main unit 4” from the rear so that the “MTC shuttle section 3” can be inserted

into behind the “MTC guide cover 1” on the right rear side when viewed from the front of the

main unit.

(2) Check to see if the head of the mounter can move to the pick-up position of the shuttle when

the conveyor rail height is aligned with that of the reference rail.

CAUTION

①

②

③

①

MTC guide cover

② Cover RUR

③ MTC shuttle section

④ MTC main unit

④

Part 2 Detailed Description of Each Function Chapter 12 Handling the Optional Devices

12-50

(3) Connect each cable and an air tube to the “MTC power connector 1,” the “signal connector 2”

and the “air joint for the MTC 3” on the interface panel on the right side of the main unit.

① Power connector for the MTC

② Interface connector for the MTC

③ φ6 tube take-up port for the MTC

(4) Turn on the machine, and then make settings of the “Device enable” screen and those of the

“MTC shuttle pick position” screen both of which are invoked from the “Machine Setup”

screen.

12.8.2 Setting the MAIN board

To use a TR6SNV/TR6DNV with an RS1/1R, you have to make setting of the DIP switch on the

MAIN board.

The DIP SW 6-2 is set to OFF at the factory.

To connect this MTC to the RS-1/1R, check the setting of the board attached on it and change it as

shown below.

Machine model the MTC is connected to

DIPSW6-2

RS-1/1R ON

Machine model other than an RS-1/1R

OFF

To check the MAIN board, remove the cover ① of the MTC.

Note:

Be sure to use the cables and the air tube supplied with the MTC.

①

②

③

Front

Rear

Part 2 Detailed Description of Each Function Chapter 12 Handling the Optional Devices

12-51

When you set the DIP SW 6-2 located at the position ② of the MAIN board to ON, the

TR6SNV/TR6DNV that has been remodeled and whose software has been upgraded can be used

with the RS-1/1R. When you set the DIP SW 6-2 to OFF, the MTC can be connected to a

machine model other than an RS-1/1R with which the MTC can be used.

Machine model the MTC is connected to:

Other than an RS-1/1R

Machine model the MTC is connected to:

RS-1/1R

To avoid any accident caused by sudden activation of the machine,

turn off the power.

CAUTION