RS-1_instruction manual.pdf - 第309页

Part 1 Basic Operat ion Chapter3 D aily maintenance 3- 17 Lubrication it em A ppl ying of oil to a noz zl e after cleaning it Lubrication fr equency : Every week T ools to be used: Air gun, co tton sw ab and waste cloth …

Part 1 Basic Operation Chapter3 Daily maintenance

3-16

Where to clean

Nozzle

Cleaning frequency:

Every week

How to clean

Cleaning of the nozzle

Tool to be used:

Ultrasonic cleaner

Recommended solution:

IPA

1) Dampen the entire nozzle whose number is from 7500 to 7504, 7509 in alcohol, and clean it with an

ultrasonic cleaner or similar tool for five minutes.

2) To prevent the urethane section of the nozzle tip from being peeled off by cleaning it with alcohol,

use the jig to turn the nozzle whose number is 7505 to 7508 upside down. Then, clean it with an

ultrasonic cleaner so that its tip cannot be dampened in alcohol.

3) Dampen soft cloth with alcohol and use it to clean the urethane part and any part of the nozzle

diffuser on which stains remain stuck to even after you use a supersonic cleaning bath to clean it.

4) After cleaning the nozzle, follow the description of “Applying oil to a nozzle after cleaning it” on the

next page and lubricate the nozzle to prevent its inside from being rusted.

CAUTION

Never use solution (such as acetone) other than alcohol.

The nozzle diffuser may be discolored.

In addition, solution may catch fire. Treat it with enough care.

CAUTION

While you are cleaning the nozzle, be sure to wear a protective mask for

organic odor.

IPA contains a substance harmful to your body.

CAUTION

Never disassemble the nozzle.

Jig block or similar

substance

Urethane part

Beaker or similar

container

Alcohol

We ask you to prepare

the beaker, jib block, etc.

on your side.

Part 1 Basic Operation Chapter3 Daily maintenance

3-17

Lubrication item

Applying of oil to a nozzle after cleaning it

Lubrication frequency:

Every week

Tools to be used:

Air gun, cotton swab and waste cloth

Oil to be used:

New Defrex No.1

If you leave the nozzle without doing anything to it after cleaning it, the inside of the nozzle may be

rusted.

Follow the procedure below to apply oil to the nozzle slider.

1) After cleaning the nozzle, use an air gun or similar device to blow off alcohol remaining in the nozzle.

2) Apply one drop of oil to the section shaded in the figure below (section protruded from the nozzle

inner when you push the nozzle slider in the direction indicated with the arrow mark ) with a

cotton swab whose half part is dampened with oil.

3) Move the nozzle slider up and down twenty to thirty times to spread oil over the entire nozzle slider.

4) Wipe off excessive oil around the nozzle with clean waste cloth.

5) After applying oil to the nozzle slider, return the nozzle to the ATC unit, and select the [Machine

setup] command and the [Nozzle setup] command in this order.

(Refer to Section 8.3.2.3 “Nozzle setup”)

CAUTION

1) Do not use oil any other than New Defrex Oil No. 1 to a nozzle.

If you use oil whose viscosity is high such as grease, the nozzle

slider cannot return to its original position normally.

2) Be sure to return the nozzle to the ATC unit instead of the head.

Nozzle slider

②

Move up and down the

nozzle slider 20 to 30 times.

①

Apply oil to this part with a

cotton swab dampened with oil.

Part to which oil

should be applied

③

Wipe off excessive oil

with a waste cloth.

Part 1 Basic Operation Chapter3 Daily maintenance

3-18

Where to clean

Nozzle outer

Cleaning frequency:

Every month

How to clean

Clearing of the nozzle outer

Tool to be used:

Cotton swab and

waste cloth