FUJI错误代码查询.pdf - 第1071页
Remedy: Check all the appropriate sensors. Remove the board from the machine. ------------------------------ Code: 13010025 Display: CHECK PCB_Y in HEADER Used by: CP3,CP4-1,CP4-2,CP4- 3,CP5,CP6,CP6M,Cp65,CP652C,CP642,CP…
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,IP1,IP3,QP242
,QP201
Cause: A communication error occurred during automatic downloading.
Remedy: Transmit the program on which the error occurred. The program name is displayed in the
message.
------------------------------
Code: 1301001D
Display: Can't load program Transmit (program name)
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,IP1,IP3,QP242
,QP201
Cause: Communication process error.
Remedy: Transmit the program on which the error occurred. The program name is displayed in the
message.
------------------------------
Code: 1301001E
Display: Program not found Transmit (program name)
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3GP2,GP3,IP1,I
P3,QP242,QP201
Cause: The program was not found.
Remedy: Transmit the program on which the error occurred. The program name is displayed in the
message.
------------------------------
Code: 13010020
Display: Program not reserved
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,IP1,IP3,QP242
,QP201
Cause: The reserved program name was not saved.
Remedy: Change the program or perform the operation again.
------------------------------
Code: 13010022
Display: MCS Process Error. code ****
Used by: CP3,GL2,GSP2,GSP3,IP1
Cause: There was an error in MCS-16. **** represents the error code.
Remedy: Find the error code in the appropriate manual, and manage it.
------------------------------
Code: 13010023
Display: FENCE
Used by: IP3,QP242,QP201
Cause: The fence opened while the conveyor width was being adjusted.
Remedy: Close the open fence.
------------------------------
Code: 13010024
Display: UNEXPECTED PCB
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP6,IP1,IP3,Q
P242,QP201
Cause: During follow-up, while the conveyor width was being changed, the board detector sensor was
activated.
第 1070 页
Remedy: Check all the appropriate sensors. Remove the board from the machine.
------------------------------
Code: 13010025
Display: CHECK PCB_Y in HEADER
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,Cp65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP6,IP1,IP3,Q
P242,QP201
Cause: The chosen board conveyor width for the following board and the PCB_Y heading are too large.
Remedy: Inspect the PCB_Y heading. Check that the current conveyor width is correct. Use the
command keys [SET], [SERVO] and [C WIDTH] to check or adjust the conveyor width.
------------------------------
Code: 13010026
Display: CHECK FOLLOWER LMS OT
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,Cp65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP6,IP1,IP3,Q
P242,QP201
Cause: The conveyor width overtravel sensor was activated.
Remedy: Check the board width, or check the follow-up sensor.
------------------------------
Code: 13010027
Display: Check Notch
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL5,GL541,GSP5,GP2,GP3,GP6,IP1,IP3,QP242,QP201
Cause: When the machine attempted to change the conveyor width setting, either the notch did not fit, or
the notch was not removed when conveyor width adjustment finished.
Remedy: Check that the notch advances and retracts using the I/O borad. Check that each conveyor
width is correct.
------------------------------
Code: 13010028
Display: Check Backup Pin
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP5,GP2,GP3,GP6,IP1,IP3,QP242,QP201
Cause: The backup pin was detected while the conveyor width was being set.
Remedy: Check the backup pin.
------------------------------
Code: 13010029
Display: CONV Adjust Time Up
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP6,IP1,IP3,Q
P242,QP201
Cause: The conveyor did not reach its target width during the preset time allowed for adjustment.
Remedy: Check the conveyor width adjustment motor, and check the encoder.
------------------------------
Code: 1301002A
Display: Conveyor Adjust Is Not Permitted
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL5,GL541,GSP5,GP2,GP3,GP6,IP3,QP242,QP201
Cause: Permission is not given to adjust the conveyor width.
Remedy: Check that all the conditions required for permission to be given have been fulfilled.
------------------------------
Code: 1301002C
第 1071 页
Display: I/D_Conv Time up Check I/D_conveyor
Used by: CP3,GL2,GSP2,GSP3,IP1
Cause: A board is caught on the ID conveyor.
Remedy: Send the caught board through. Check that the ID conveyor's board detection sensor is
operating correctly.
------------------------------
Code: 1301002D
Display: WARNING: Check Push Plate
Used by: GSP2,GSP3
Cause: The board lifter has not been removed.
Remedy: Remove the board lifter.
------------------------------
Code: 1301002E
Display: WARNING: Check Vacuum plate
Used by: GSP2,GSP3
Cause: The board holder has not been removed.
Remedy: Remove the board holder.
------------------------------
Code: 1301002F
Display:
Used by:
Cause: The board holder could not be clamped.
Remedy: Clamp the board holder. Alternately, remove the board holder and check the sensor (IN3-24
REMOVE_S_PLATE).
------------------------------
Code: 13010030
Display: Sectional Transmitting... (PROG NAME)
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP551,GP6,IP
1,IP3,QP242,QP201
Cause: The program could not be changed while part of the reservation program was being transmitted.
Remedy: Wait until the section is transmitted, and then either re-execute the function or transmit the
reservation program.
------------------------------
Code: 13010031
Display: Sectional Transmit Error (PROG NAME)
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,IP1,IP2,IP3,QP
242,QP201
Cause: The reservation program was invalid due to a transmission error, so the program could not be
changed.
Remedy: Re-transmit the reservation program.
------------------------------
Code: 13010032
Display: "Family Board Error"
Used by: QP242,QP201
Cause: When performing a seamless changeover using a pilot board, the production order table specified
a production program with either a different family board name or a different board width (QP2).
Remedy: Change the production order table.
------------------------------
Code: 13010033
第 1072 页