FUJI错误代码查询.pdf - 第872页

Cause: Power out of phase. One of the three phases for the power is not connected. Remedy: Check to ensure that all wires for the three phases are not broken, or have any shorts. ------------------------------ Code: 1211…

100%1 / 5282
Cause: Momentary maximum torque. Operation was performed for several seconds at significantly over
the rated torque.
Remedy: Check to ensure that there is no interference or that the axis movement is not impeded. In
addition, check to ensure that none of the motor power lines are broken (U,V,W), or that there are no
shorts.
------------------------------
Code: 1211003b
Display: Servo amplifier error.
Used by:
Cause: DB overload. During dynamic braking, the rotational energy is more than the DB resistance
capacity.
Remedy: The emergency stop process could be incorrect. If this occurs frequently, contact Fuji.
------------------------------
Code: 1211003c
Display: Servo amplifier error.
Used by:
Cause: Initial resistance overload. The base power has been repeatedly turned on and off.
Remedy: Check for a short in the power line, or if the wire is broken, when this condition occurs.
Contact Fuji if no abnormalities are found, because the servo amplifier could be damaged.
------------------------------
Code: 1211003d
Display: Servo amplifier error.
Used by:
Cause: Heat sink is too hot. The heat sink for the servo pack is too hot.
Remedy: Check for abnormalities in the base circuitry or in the wiring for the motor power.
Contact Fuji if no abnormalities are found, because the servo amplifier could be damaged.
------------------------------
Code: 1211003e
Display: Servo amplifier error.
Used by:
Cause: Encoder feedback error. Information from the encoder is abnormal.
Remedy: Check for breaks in the encoder wiring, or for bad connections.
Contact Fuji if no abnormalities are found, because the servo amplifier could be damaged.
------------------------------
Code: 1211003f
Display: Servo amplifier error.
Used by:
Cause: Erratic movement detected. Motor was out of control.
Remedy: Check the base circuit wiring, motor power wiring, and encoder wiring for any abnormalities.
Contact Fuji if no abnormalities are found, because the servo amplifier could be damaged.
------------------------------
Code: 12110040
Display: Servo amplifier error.
Used by:
Cause: Positioning deviation is too large. Positioning deviation pulse was over the set value.
Remedy: Check to ensure that the deviation setting is appropriate.
Investigate the reason for it being out of control.
------------------------------
Code: 12110041
Display: Servo amplifier error.
Used by:
第 871 页
Cause: Power out of phase. One of the three phases for the power is not connected.
Remedy: Check to ensure that all wires for the three phases are not broken, or have any shorts.
------------------------------
Code: 12110042
Display: Servo amplifier error.
Used by:
Cause: Watch dog error. Abnormal SERCOS communication has occurred.
Remedy: Check to ensure that the digital operator is not connected.
Contact Fuji if this occurs frequently, because the SERCOS unit could be damaged.
------------------------------
Code: 12110043
Display: Servo amplifier error.
Used by:
Cause: MST, MDT error. SERCOS communication is abnormal.
Remedy: Check the fiber optic connections and make sure the digital operator is not connected.
Contact Fuji if no abnormalities are found, because the SERCOS board could be damaged.
------------------------------
Code: 12110044
Display: Boot timeout.
Used by:
Cause: RTX Servo filter execution file is timeout of boot.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12110045
Display: The magnetic pole detection failure.
Used by:
Cause: The execution of the Detected Magnet Pole is timeout.
Remedy: Check to ensure that the linear motor axis is no interference or that the axis movement is not
impeded.
------------------------------
Code: 12110046
Display: Program error.
Used by:
Cause: The specified function is effective only with the linear motor.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12110047
Display: The magnetic pole detection failure.
Used by:
Cause: It has executed magnetic pole detection.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12110048
Display: Program error.
Used by:
Cause: An indicated axis is registered on the other operation control at present.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12110049
Display: System error.
Used by:
第 872 页
Cause: The fault which it is impossible to recover occurs.
Remedy: This error is impossible to detect.Get a trace file and contact FUJI.
------------------------------
Code: 1211004A
Display: Coordinate motion error.
Used by:
Cause: The draw time of the specified diagram is too long.
Remedy: Check the diagram information.Contact Fuji if no abnormalities are found, and get a trace file.
------------------------------
Code: 1211004B
Display: Profile error.
Used by:
Cause: The profile could not be made as specified.
Remedy: Check to ensure that there is no interference or that the axis movement is not impeded.
Contact Fuji if no abnormalities are found.
------------------------------
Code: 1211004C
Display: Coordinate motion error.
Used by:
Cause: The coodinate motion of the specified handle isn't declarative in the use.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12110050
Display: Board error.
Used by:
Cause: The servo board set in the servo initialization file is not supported.
Remedy: Check the setting in the servo initialization file, and that the servo control board is correct.
Contact Fuji if no abnormalities are found, because the board could be damaged.
------------------------------
Code: 12110051
Display: Failed to create object.
Used by:
Cause: Failed to create a servo object.
Remedy: Reinstall the software because the initial installation could have failed.
Contact Fuji if this error is not corrected, because the servo control board could be damaged.
------------------------------
Code: 12110052
Display: Abnormal parameter.
Used by:
Cause: The ADC number setting does not exist.
Remedy: Check the value in the servo initialization file.
If no abnormalities are found, reinstall the software.
------------------------------
Code: 12110053
Display: Abnormal parameter.
Used by:
Cause: An invalid value has been set in the parameter's argument (axis number).
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110054
Display: Abnormal parameter.
第 873 页