FUJI错误代码查询.pdf - 第2079页

Cause: A module could not be loaded. The module may have been destroyed. Remedy: Re-install the software. ------------------------------ Code: 2100E605 Display: <****> not found Used by: Cause: The specified comman…

100%1 / 5282
Cause: Data could not be written to the module test print file.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100E528
Display: module test print out file open error
Used by:
Cause: The module test print file could not be opened.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100E529
Display: printer file write error
Used by:
Cause: Data could not be written to the print file.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100E52A
Display: device not ready
Used by:
Cause: The specified device (floppy disk drive or printer) is not in the operating status.
Remedy: Make sure that the floppy disk drive lock lever is fully closed and that the printer is turned on
and set on-line.
------------------------------
Code: 2100E52B
Display: device install list open error
Used by:
Cause: The install list for the specified device could not be opened.
Remedy: Re-install the software.
------------------------------
Code: 2100E52C
Display: Comm board and environment file setting mismatch.
Used by:
Cause: There are differences between the communication board data described in the environmental
constants and the installed communication board.
Remedy: Install the communication boards according to the procedure described in the environmental
constants. Or make the correct settings on the communication board.
------------------------------
Code: 2100E602
Display: not enough memory !
Used by:
Cause: Not possible to allocate sufficient memory area.
Remedy: Re-boot MCS.
------------------------------
Code: 2100E603
Display: command error
Used by:
Cause: An error occurred when a command was input.
Remedy: Re-execute the function. If the error recurs, re-install the software.
------------------------------
Code: 2100E604
Display:
Used by:
第 2078 页
Cause: A module could not be loaded. The module may have been destroyed.
Remedy: Re-install the software.
------------------------------
Code: 2100E605
Display: <****> not found
Used by:
Cause: The specified command does not exist.
Remedy: Correct the input command if this error occurred due to a direct command. Contact Fuji if the
error did not occur due to a direct command.
------------------------------
Code: 2100EA00
Display: parameter error
Used by:
Cause: The start-up parameters are incorrect.
Remedy: Contact Fuji.
------------------------------
Code: 2100EA01
Display: message file open error
Used by:
Cause: The string file could not be opened.
Remedy: Contact Fuji.
------------------------------
Code: 2100EA02
Display: File descriptor not found
Used by:
Cause: The file descriptor could not be loaded to memory.
Remedy: Re-install the software.
------------------------------
Code: 2100EA03
Display: Line descriptor load error
Used by:
Cause: The line descriptor could not be loaded to memory.
Remedy: Re-install the software.
------------------------------
Code: 2100EA04
Display: Error: can't create TTYS data
Used by:
Cause: The TTYS data file could not be created.
Remedy: Re-boot MCS. If the error recurs, re-install from the OS.
------------------------------
Code: 2100EA05
Display: Error: can't create Services data
Used by:
Cause: The Services data file could not be created.
Remedy: Re-boot MCS. If the error recurs, re-install from the OS.
------------------------------
Code: 2100EA06
Display: Error: can't create pipes data
Used by:
Cause: The Pipes data file could not be created.
Remedy: Re-boot MCS. If the error recurs, re-install from the OS.
第 2079 页
------------------------------
Code: 2100EA07
Display: Error: can't create Host data
Used by:
Cause: The Host data file could not be created.
Remedy: Re-boot MCS. If the error recurs, re-install from the OS.
------------------------------
Code: 2100EA08
Display: terminal path open error
Used by:
Cause: The terminal path could not be set.
Remedy: Re-boot MCS. If the error recurs, re-install from the OS.
------------------------------
Code: 2100EA09
Display: event link error
Used by:
Cause: A terminal event could not be linked.
Remedy: Re-boot MCS.
------------------------------
Code: 2100EA0A
Display: terminal setting error
Used by:
Cause: The terminal could not be initialized.
Remedy: Re-boot MCS.
------------------------------
Code: 2100EA80
Display: RS-232C CH%d data is out of range
Used by:
Cause: Data in channel ** of the RS-232C port is out of range.
Remedy: Correct the appropriate part of the line descriptor.
------------------------------
Code: 2100EA81
Display: LAN #%d data is out of range
Used by:
Cause: Data in LAN number ** is out of range.
Remedy: Correct the appropriate part of the line descriptor.
------------------------------
Code: 2100EA82
Display: Line name (%s) duplicated at RS-232C No.%d & RS-232C CH%d.
Used by:
Cause: The same line nickname (**) is duplicated for the displayed RS-232C channels (* and *).
Remedy: Correct the appropriate part of the line descriptor.
------------------------------
Code: 2100EA83
Display: Line name (%s) duplicated at RS-232C No.%d & LAN No.%d
Used by:
Cause: The same line nickname (**) is duplicated for the displayed RS-232C channel (*) and LAN number
(*).
Remedy: Correct the appropriate part of the line descriptor.
------------------------------
Code: 2100EA84
第 2080 页