FUJI错误代码查询.pdf - 第860页

Cause: There are no leads on the part where a lead coplanarity check is occurring. Remedy: Do not perform a lead coplanarity check for parts without leads. Verify that the part data (number of leads) is set correctly. --…

------------------------------

Code: 121???05

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Either an internal processing error or a time up condition occurred when the LLL board

coplanarity calculation command was executed.

Remedy: Verify that the part in question has either 2 or 4 sides with leads. The coplanarity calculation

command cannot be used for parts with leads on only 1 side. If the LLL baud rate is less than 9600bps,

set it to 9600bps or higher. (Time up) If the problem continues, turn the power off.

------------------------------

Code: 121???06

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An error occurred when an encoder resolution setting was attempted for an LLL board.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???07

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Either an error or a time up condition occurred when attempting to output engineering data to

the LLL board.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???08

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Either an error or time up condition occurred when attempting to set parameter data (linearity

tolerance, coplanarity tolerance) for an LLL board.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???09

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Either an error or a time up condition occurred when the LLL board scan-end command was

executed. If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) Leads could

not be measured. (Error) Check connections of encoder and sensor cables.

Remedy: Set the LLL baud rate to 9600bps or higher. Is the lead length indicated in part data

significantly different from the actual lead length? part data items: Body-Length, Body-Width

------------------------------

Code: 121???0A

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Another LLL measurement command is in progress.

Remedy: Restart the machine.

------------------------------

Code: 121???0B

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

第 859 页

Cause: There are no leads on the part where a lead coplanarity check is occurring.

Remedy: Do not perform a lead coplanarity check for parts without leads. Verify that the part data

(number of leads) is set correctly.

------------------------------

Code: 121???0C

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Either an error or a time up condition occurred when the LLL board linearity calculation

command was executed.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???0D

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Either an internal processing error or a time up condition occurred when the LLL board linearity

calculation command was executed.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???0E

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An error occurred when the linearity calculation result was received or checked. Either a

communication time up condition occurred, or no leads were detected, resulting in no calculation result.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off. Also verify that the part size is correct.

------------------------------

Code: 121???0F

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An attempt to obtain linearity calculation results from the LLL board ended in failure. Either a

communication time up occurred, or the lead bend amount exceed the permissible range.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???10

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An error occurred when the coplanarity calculation result was received or checked. A

communication time up occurred.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???11

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An attempt to obtain coplanarity calculation results from the LLL board ended in failure. Either a

communication time up occurred, or the lead bend amount exceed the permissible range.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

第 860 页

------------------------------

Code: 121???21

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: A command sequence error occurred. The command could not be executed at the LLL board.

Remedy: Restart the system, and repeat the operation from the beginning.

------------------------------

Code: 121???22

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Insufficient data error. LLL board calculation ended in failure due to insufficient data. Lead

measurement was not performed, and no pulse was received from the encoder. A coplanarity calculation

was attempted after scanning 1 side.

Remedy: Set the Lead-Length (in part data) as accurately as possible. Increase the Scan Offset to permit

measurement of the full length of the lead. Lead coplanarity checks are possible for SOIC or QFP parts.

------------------------------

Code: 121???23

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Parameter error. The received data is invalid for the LLL..

Remedy: Check the Coplanarity item in part data.

------------------------------

Code: 121???24

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Invalid command. The attempted command is invalid for the LLL..

Remedy: Execute a reset start.

------------------------------

Code: 121???30

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Serial communication "receive overrun" error.

Remedy: Restart the system and repeat the operation from the beginning.

------------------------------

Code: 121???31

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Serial communication "parity" error.

Remedy: Restart the system and repeat the operation from the beginning.

------------------------------

Code: 121???32

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Serial communication "framing" error.

Remedy: Restart the system and repeat the operation from the beginning.

------------------------------

Code: 121???40

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Communication with "Sensor 0 EEPROM Readback Error sensor 0" is not occurring. Sensor

cable is severed or disconnected.

第 861 页