FUJI错误代码查询.pdf - 第1123页

Used by: GSP2,GSP3,IP1,IP2,NP132,NP133,NP2,QP3 Cause: The board lifter could not clamp or unclamp within the preset time limit. Remedy: Check to see whether or not there is something interfering with the movement of the …

100%1 / 5282
------------------------------
Code: 15040240
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040241
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040242
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040243
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040301
Display: PCB Loading NG
CHECK PCB
CHECK MAIN-CONVEYOR
Used by: CP3,GSP2,GSP3,IP2,NXTP
Cause: The board cannot be loaded properly.
Remedy: Place the board in its correct position. Check the movement of the stopper at the I/O display
OUT2-26 B_STOPPER_OFF and IN5-19 IN_STOPPER_SW.
------------------------------
Code: 15040302
Display: CHECK LOADER
Used by: CP3
Cause: The loader is not in its original position.
Remedy: Return the loader to its original position.
------------------------------
Code: 15040303
Display: Duplex Loading
Used by: GSP2,GSP3
Cause: Two boards were loaded. The appropriate sensor is connected to IN2-12 DOUBLE_PCB.
Remedy: Remove the boards.
------------------------------
Code: 15040304
Display: Cycle Alarm CLAMP(GSP2)
CYCLE NG Lifter(IP2)
Clamp Error(IP1)
PCB lifter error!(NP2,QP3)
第 1122 页
Used by: GSP2,GSP3,IP1,IP2,NP132,NP133,NP2,QP3
Cause: The board lifter could not clamp or unclamp within the preset time limit.
Remedy: Check to see whether or not there is something interfering with the movement of the clamp.
Adjust the board lifter. Adjust the board lifter's upper and lower limit position.
------------------------------
Code: 15040305
Display: Cycle Alarm PIN
Clamper NG
Used by: GL2,GL5,GL541,IP1,IP2,NP132,NP133
Cause: A reference pin cylinder alarm occurred. The board positioning pin could not enter the reference
hole.
Remedy: Adjust the reference pin cylinder's advance and retract movement. If the pin enters the
reference hole and this message still occurs, check to see that the pin sensor dog moves into the sensor.
------------------------------
Code: 15040306
Display: CHECK FEEDER
Used by: CP3
Cause: The board feeder cylinder could not advance to the arrival position within the preset time.
Remedy: Remove any interfering objects.
------------------------------
Code: 15040307
Display: CHECK TABLE
Lifter Up/Down Error
Used by: CP3
Cause: The table could not raise or lower itself within the preset limits. Something is interfering with the
movement of the XY table.
Remedy: Remove all obstacles to board movement.
------------------------------
Code: 15040308
Display: CHECK JAW
Used by: CP3
Cause: The board feeding pin could not raise or lower itself within the preset time.
Remedy: Remove any obstacles to board movement.
------------------------------
Code: 15040309
Display: TABLE BASE NG
Used by: CP3
Cause: The table base did not move up or down correctly.
Remedy: Check that no parts or garbage is sitting under the parts table. Check IN2-30 TABLE BASE
DWD and IN2-31 TABLE BASE DWN at the I/O display. Also, turn OUT2-2 TABLE BASE DWN on and off
to check the sensor (CP3).
------------------------------
Code: 1504030A
Display: Cycle Alarm Lifter
Lifter
Used by: GL2,GL5,GL541,GSP2,GSP3
Cause: The board lifter could not clamp or unclamp within the preset time limit.
Remedy: Check to see whether or not there is something interfering with the movement of the clamp.
Adjust the board lifter. Adjust the board lifter's upper and lower limit position.
------------------------------
Code: 1504030B
第 1123 页
Display: Cycle Alarm STOPPER(IP,IP2)
Stopper ascent error!(NP2,QP3)
Used by: IP1,IP2,NP132,NP133,NP2,QP3
Cause: Stopper cylinder alarm.
Remedy: Adjust the advance and retract positions of the stopper cylinder.
------------------------------
Code: 1504030C
Display: Cycle Alarm LOADER NOTCH
Used by: GL2,GL5,GL541,IP1,IP2
Cause: Loader notch cylinder alarm.
Remedy: Adjust the advance and retract positions of the loader notch cylinder.
------------------------------
Code: 1504030D
Display: Cycle Alarm PCB_planer L or R
Used by:
Cause: The board pusher could not operate within the set time limit.
Remedy: Check that the movement of the board pusher is not being interfered with.
------------------------------
Code: 1504030E
Display: Cycle Alarm Lifter U or D
Used by: GSP2,GSP3,GSP5,GP2,GP3,GP551,GP6
Cause: The board lifter could not operate within the set time limit.
Remedy: Check that the movement of the board lifter is not being interfered with.
------------------------------
Code: 1504030F
Display: TABLE UWD NG
Used by: CP3
Cause: The XY table could not raise itself.
Remedy: Check that there is nothing interfering with the XY table's guide rail and the in or out-conveyor.
At the I/O display, toggle OUT1-18 TABLE UWD and OUT1-19 TABLE DWD on and off, and check IN2-5
FEEDER FWD.
------------------------------
Code: 15040310
Display: TABLE DWD NG
Used by: CP3
Cause: The XY table could not lower itself.
Remedy: Check that there is nothing interfering with the XY table's guide rail and the in or out-conveyor.
At the I/O display, toggle OUT1-18 TABLE UWD and OUT1-19 TABLE DWD on and off, and check IN2-5
FEEDER FWD.
------------------------------
Code: 15040311
Display: FEEDER FWD NG
Used by: CP3
Cause: The board loader cylinder could not advance.
Remedy: Check that there is nothing interfering with the board loaderls ability to move. At the I/O
display, toggle OUT1-16 FEEDER FWD and OUT1-17 FEEDER BWD on and off, and check IN2-5 FEEDER
FWD.
------------------------------
Code: 15040312
Display: FEEDER FWD NG
Used by: CP3
第 1124 页