FUJI错误代码查询.pdf - 第526页

time.Something interfered with the movement of the axis. Remedy: Check the load on the servo axis.Check the motor, servo amp connectors and wiring. Remove any obstacles to movement. ------------------------------ Code: 1…

------------------------------

Code: 1205202A

Display:

Used by:

Cause: The axis moved beyond its limit.

Remedy: Check the coordinates in the program and the values in Proper data.

------------------------------

Code: 1205202B

Display:

Used by:

Cause: The axis moved beyond its limit.

Remedy: Check the coordinates in the program and the values in Proper data.

------------------------------

Code: 1205202C

Display:

Used by:

Cause: The axis moved beyond its limit.

Remedy: Check the coordinates in the program and the values in Proper data.

------------------------------

Code: 1205202D

Display:

Used by:

Cause: The axis moved beyond its limit.

Remedy: Check the coordinates in the program and the values in Proper data.

------------------------------

Code: 1205202F

Display:

Used by:

Cause: The axis moved beyond its limit.

Remedy: Check the coordinates in the program and the values in Proper data.

------------------------------

Code: 12052030

Display:

Used by: GSP5

Cause: An MX axis cycle stop has occurred. The servo axis could not reach its tarte in the specified time.

Something interfered with the movement of the axis.

Remedy: Check the load on the servo axis.Check the motor, servo amp connectors and wiring. Remove

any obstacles to movement.

------------------------------

Code: 12052031

Display:

Used by: GSP5

Cause: An MYL axis cycle stop has occurred. The servo axis could not reach its tarte in the specified

time.Something interfered with the movement of the axis.

Remedy: Check the load on the servo axis.Check the motor, servo amp connectors and wiring. Remove

any obstacles to movement.

------------------------------

Code: 12052032

Display:

Used by: GSP5

Cause: An MYR axis cycle stop has occurred. The servo axis could not reach its tarte in the specified

第 525 页

time.Something interfered with the movement of the axis.

Remedy: Check the load on the servo axis.Check the motor, servo amp connectors and wiring. Remove

any obstacles to movement.

------------------------------

Code: 12052033

Display: Cycle Alarm SERVO SS

Used by: QP132

Cause: An SS servo axis cycle alarm has occurred. The servo axis did not reach the intended value within

the scheduled amount of time. Or there was something causing interference with the axis.

Remedy: Make sure that the servo is not overloaded. Check the connectors and wiring of the motor and

servo amp. Inspect the servo amp. Remove any objects that may be interfering with the axis.

------------------------------

Code: 12052034

Display: Cycle Alarm SERVO MX

Used by: QP132

Cause: An MX servo axis cycle alarm has occurred. The servo axis did not reach the intended value

within the scheduled amount of time. Or there was something causing interference with the axis.

Remedy: Make sure that the servo is not overloaded. Check the connectors and wiring of the motor and

servo amp. Inspect the servo amp. Remove any objects that may be interfering with the axis.

------------------------------

Code: 12052035

Display: Cycle Alarm SERVO MY

Used by: QP132

Cause: An MY servo axis cycle alarm has occurred. The servo axis did not reach the intended value

within the scheduled amount of time. Or there was something causing interference with the axis.

Remedy: Make sure that the servo is not overloaded. Check the connectors and wiring of the motor and

servo amp. Inspect the servo amp. Remove any objects that may be interfering with the axis.

------------------------------

Code: 12052036

Display: Cycle Alarm SERVO PI

Used by: QP132

Cause: A PI servo axis cycle alarm has occurred.The servo axis did not reach the intended value within

the scheduled amount of time. Or there was something causing interference with the axis.

Remedy: Make sure that the servo is not overloaded. Check the connectors and wiring of the motor and

servo amp. Inspect the servo amp. Remove any objects that may be interfering with the axis.

------------------------------

Code: 12052037

Display: Cycle Alarm SERVO PO

Used by: QP132

Cause: A PO servo axis cycle alarm has occurred.The servo axis did not reach the intended value within

the scheduled amount of time. Or there was something causing interference with the axis.

Remedy: Make sure that the servo is not overloaded. Check the connectors and wiring of the motor and

servo amp. Inspect the servo amp. Remove any objects that may be interfering with the axis.

------------------------------

Code: 12052038

Display: Cycle Alarm SERVO F

Used by:

Cause: An F servo axis cycle alarm has occurred.The servo axis did not reach the intended value within

the scheduled amount of time. Or there was something causing interference with the axis.

Remedy: Make sure that the servo is not overloaded. Check the connectors and wiring of the motor and

servo amp. Inspect the servo amp. Remove any objects that may be interfering with the axis.

第 526 页

------------------------------

Code: 12052039

Display: "UP Elevator UP/DOWN timeout"

Used by: CP652C

Cause: The UP elevator did not arrive at the upper (or lower) limit within the specified time after an

instruction to move up (or down) was issued. This error will also occur if the lower deceleration position

sensor is on when the elevator has arrived at the upper limit, or if the upper deceleration position sensor

is on when the elevator has arrived at the lower limit.

Remedy: If the elevator has arrived at the upper (or lower) limit, make sure that the upper (or lower) limit

sensor and the upper (or lower) deceleration position sensor are functioning normally. When the elevator

is moving up, the elevator upper limit and upper deceleration position sensors (X082 and X092) should be

off and the lower deceleration position sensor (X093) should be on. When it ismoving down, the lower

limit and lower deceleration position sensors (X083 and X093) should be off and the up er deceleration

position sensor (X092) should be on.

------------------------------

Code: 1205203A

Display: "UP Elevator Interlock ON"

Used by: CP652C

Cause: Either UP elevator pallet passage check sensor 1 (on the IN position side) or UP elevator pallet

passage check sensor 2 (on the PPS6 side) was tripped while the UP elevator was operating.

Remedy: Make sure that nothing is obstructing UP elevator operation. If there is no obstruction, perform

an I/O check to confirm input from the UP elevator pallet passage check sensors (X085 and X086,

respectively) and adjust as necessary.

------------------------------

Code: 1205203B

Display: "DOWN Elevator UP/DOWN timeout"

Used by: CP652C

Cause: The DOWN elevator did not arrive at the upper (or lower) limit within the specified time after an

instruction to move up (or down) was sent. This error will also occur if the lower deceleration position

sensor is on when the elevator has arrived at the upper limit, or if the upper deceleration position sensor

is on when the elevator has arrived at the lower limit.

Remedy: If the elevator has arrived at the upper (or lower) limit, make sure that the upper (or lower) limit

sensor and the upper (or lower) deceleration position sensor are functioning normally. When the elevator

is moving up, the elevator upper limit and upper deceleration position sensors (X0A2 and X09A) should be

off and the lower deceleration position sensor (X0AB) should be on. When it ismoving down, the lower

limit and lower deceleration position sensors (X0A3 and X0AB) should be off and the up er deceleration

position sensor (X0AA) should be on.

------------------------------

Code: 1205203C

Display: "DOWN Elevator Interlock ON"

Used by: CP652C

Cause: The DOWN elevator pallet passage check sensor was tripped while the UP elevator was operating.

Remedy: Make sure that nothing is obstructing DOWN elevator operation. If there is no obstruction,

perform an I/O check to confirm input from the DOWN elevator pallet passage check sensor (X0A5)

andadjust as necessary.

------------------------------

Code: 1205203D

Display: "Cycle Alarm DF or DR"

Used by: CP652C

Cause: Servo axis DF or DR did not reach the target position within the expected time. This error may be

caused by interference from another object, an excessive load, or an abnormality in a servo system circuit.

第 527 页