FUJI错误代码查询.pdf - 第874页

Used by: Cause: The setting for the servo controller board number is incorrect. Remedy: Reinstall the software because the initial installation could have failed. ------------------------------ Code: 12110055 Display: Ab…

100%1 / 5282
Cause: The fault which it is impossible to recover occurs.
Remedy: This error is impossible to detect.Get a trace file and contact FUJI.
------------------------------
Code: 1211004A
Display: Coordinate motion error.
Used by:
Cause: The draw time of the specified diagram is too long.
Remedy: Check the diagram information.Contact Fuji if no abnormalities are found, and get a trace file.
------------------------------
Code: 1211004B
Display: Profile error.
Used by:
Cause: The profile could not be made as specified.
Remedy: Check to ensure that there is no interference or that the axis movement is not impeded.
Contact Fuji if no abnormalities are found.
------------------------------
Code: 1211004C
Display: Coordinate motion error.
Used by:
Cause: The coodinate motion of the specified handle isn't declarative in the use.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12110050
Display: Board error.
Used by:
Cause: The servo board set in the servo initialization file is not supported.
Remedy: Check the setting in the servo initialization file, and that the servo control board is correct.
Contact Fuji if no abnormalities are found, because the board could be damaged.
------------------------------
Code: 12110051
Display: Failed to create object.
Used by:
Cause: Failed to create a servo object.
Remedy: Reinstall the software because the initial installation could have failed.
Contact Fuji if this error is not corrected, because the servo control board could be damaged.
------------------------------
Code: 12110052
Display: Abnormal parameter.
Used by:
Cause: The ADC number setting does not exist.
Remedy: Check the value in the servo initialization file.
If no abnormalities are found, reinstall the software.
------------------------------
Code: 12110053
Display: Abnormal parameter.
Used by:
Cause: An invalid value has been set in the parameter's argument (axis number).
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110054
Display: Abnormal parameter.
第 873 页
Used by:
Cause: The setting for the servo controller board number is incorrect.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110055
Display: Abnormal parameter.
Used by:
Cause: The acceleration time setting is outside the valid range.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110056
Display: Abnormal parameter.
Used by:
Cause: The deceleration time setting is outside the valid range.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110057
Display: The jerk ratio setting is outside the valid range (1-100).
Used by:
Cause:
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110058
Display: Abnormal parameter.
Used by:
Cause: The position parameter setting is outside the valid range.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110059
Display: Abnormal parameter.
Used by:
Cause: The GAIN table setting (Moving带归Settling带幩is invalid.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 1211005a
Display: Abnormal parameter.
Used by:
Cause: The GAIN table number setting is invalid.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 1211005b
Display: Abnormal parameter.
Used by:
Cause: The traveling speed setting is outside the valid range.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 1211005c
Display: Abnormal parameter.
Used by:
Cause: Unable to reference the gain table as the specified axis number is invalid.
Remedy: Reinstall the software because the initial installation could have failed.
第 874 页
------------------------------
Code: 1211005d
Display: Abnormal parameter.
Used by:
Cause: A parameter is not set in the GAIN table ID.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 1211005e
Display: Abnormal parameter.
Used by:
Cause: The movement operation cannot be performed because the previous goal position is not set so it
cannot be referenced.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 1211005f
Display: Abnormal parameter.
Used by:
Cause: A setting for the AD converter is invalid.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110060
Display: Abnormal parameter.
Used by:
Cause: The setting for the AD converter measurement range is outside of the valid range.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110061
Display: Abnormal parameter.
Used by:
Cause: SERCOS IDN communication that is not supported has occurred.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110062
Display: Abnormal parameter.
Used by:
Cause: SERCOS Pno communication that is not supported has occurred.
Remedy: Reinstall the software because the initial installation could have failed.
If this does not correct the error, send the trace data to Fuji.
------------------------------
Code: 12110063
Display: Abnormal parameter.
Used by:
Cause: The maximum number of simultaneous Pno and IDN access possible to the SERCOS drive has
been exceeded.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12110064
Display: Emergency stop condition.
Used by:
Cause: An axis has been given instructions to move while in emergency stop condition.
Remedy: Attempt to move the axes after releasing the emergency stop condition. If the same error occurs,
第 875 页