FUJI错误代码查询.pdf - 第2171页

Used by: Cause: <XP*42>Feeder optimization/Feeder configuration was performed selecting "Configure feeders automatically"but feeders cannot be arranged. Remedy: <XP*42>Reduce the number of part type…

------------------------------

Code: 230600A3

Display: Optimization cannot be performed if there are less than two active fiducial marks.

Used by:

Cause: Optimization cannot be performed for programs containing less than two active fiducial marks,

including skipped marks.

Remedy: Add two or more active fiducial mark sequences to the program.

------------------------------

Code: 230600A4

Display: Optimization cannot be performed because no valid placement sequences exist.

Used by:

Cause: Optimization cannot be performed because all placement sequences are skipped.

Remedy: The program must contain at least one placement sequence that is not to be skipped.

------------------------------

Code: 2306010C

Display: Tray part(s) cannot be loaded on the XP-341E.

Used by:

Cause: Package Type(PARTS/PACKCLS-/PPCMNPT) is 0*.

Remedy: The Package Type setting in the part data is incorrect. Check and correct the setting.

------------------------------

Code: 2306010E

Display: Dual Tape Feeder(s) cannot be loaded on the XP-341E.

Used by:

Cause: Package Type(PARTS/PACKCLS-/PPCMNPT) is 8*.

Remedy: The Package Type setting in the part data is incorrect. Check and correct the setting.

------------------------------

Code: 23078003

Display: Unregistered Tape Width.A feeder cannot be selected.

Used by:

Cause: <XP*42>Cannot optimize because feeder width is unknown.A registered Tape Width must be used

so that a feeder can be selected.

Remedy: <XP142>If Packaging Type is not "2:32mm Adhesive",set the tape width to "8","12","16","24",or

"32".

<XP242>If Packaging Type is not "0:Tray","2:32mm Adhesive","4:Stick Feeder"or "9:Grooved Stick

Feeder",set The Tape Width to "8","12","16","24","32","44","56","72",or "88".

------------------------------

Code: 23078005

Display: The stage-slot number is not defined.

Used by:

Cause: XP*42>No setting data exists for the stage-slot number specified in the sequence data.

Remedy: <XP*42>Either specify settings for the stage-slot number in the feeder setup data,or specify a

stage-slot number for which setting data already exists.

------------------------------

Code: 23078006

Display: The part data is not found.

Used by:

Cause: <XP*42>Data corresponding to the part number does not exist.

Remedy: <XP*42>Create the specified part number data,or specify an existing part number.

------------------------------

Code: 2307800E

Display: Feeders cannot be arranged.

第 2170 页

Used by:

Cause: <XP*42>Feeder optimization/Feeder configuration was performed selecting "Configure feeders

automatically"but feeders cannot be arranged.

Remedy: <XP*42>Reduce the number of part types and feeders being used or,for the XP-242 only,change

the "Feeder types used"setting in the "Feeder optimization"screen and then press [Execute].

------------------------------

Code: 2307800F

Display: Trays cannot be arranged.

Used by:

Cause: <XP*42>Feeder optimization/Feeder configuration was performed using the "Configure feeders

automatically"setting but trays cannot be arranged.

Remedy: <XP*42>Reduce the number of part types or trays being used.

------------------------------

Code: 23078011

Display: Optimization was performed using the [Fix feeder configuration]setting but trays could not be

arranged.

Used by:

Cause: <XP*42>Feeder optimization/Feeder configuration was performed using the "Fix feeder

configuration (Do not change feeder positions)"setting but trays could not be arranged.

Remedy: <XP*42>Check the feeder set up on the machine or optimize by selecting "Configure Feeders

Automatically"under "Feeder Configuration"in the "Feeder Optimization"screen.

------------------------------

Code: 23078018

Display: Tray size is too large to be loaded.

Used by:

Cause: <XP*42>The Tray Length or Width value in the Part Type data exceeds the maximum.(Tray

Length maximum:330mm;Tray Width maximum:276mm)

Remedy: <XP*42>Confirm that the Tray Length and Width values in the Part Type data do not exceed

330mm and 276mm.Trays larger than this cannot be loaded.

------------------------------

Code: 2307803B

Display: Stage number is not defined.

Used by:

Cause: <XP*42>Stage number is not defined.

Remedy: <XP*42>Input the Stage number.

------------------------------

Code: 23078042

Display: The necessary nozzles could not be allocated.

Used by:

Cause: <XP*42>Nozzle optimization/Nozzle configuration was optimized using the "Configure nozzles

automatically"setting but the necessary nozzles could not be allocated.

Remedy: <XP*42>Check the Nozzle Name,Minimum Nozzle Diameter and Maximum Nozzle Diameter

values in the Part Type data or reduce the number of parts types and feeders being used.

------------------------------

Code: 23078044

Display: No matching nozzle.

Used by:

Cause: <XP*42>The nozzle selected under Nozzle Name in the Part Type data is not on the machine.If a

Nozzle Name has not been set,there is no nozzle available to handle the range between the Minimum and

Maximum Nozzle Diameter values set.

Remedy: <XP*42>If optimization was performed with "Use machine nozzle configuration"selected under

第 2171 页

"Nozzle configuration"on the "Nozzle optimization screen",check the arrangement of the nozzles on the

machine.

If "Use program nozzle configuration"was selected,check the nozzle arrangement in the program.

If this does not resolve the problem,optimize using the "Configure nozzles automatically"setting.

------------------------------

Code: 23078824

Display: A required nozzle does not exist in the nozzle list on the machine.

Used by:

Cause: <XP*42>The nozzle selected under Nozzle Name in the Part Type data is not listed on the

machine.If a Nozzle Name has not been set,no listed nozzle can handle the range between the Minimum

and Maximum Nozzle Diameter values set.

Remedy: <XP*42>Check the Nozzle Name,Minimum Nozzle Diameter and Maximum Nozzle Diameter in

the Part Type data.

------------------------------

Code: 23078827

Display: A slot that has not been allocated a part number is set as an Alt.Feeder.

Used by:

Cause: <XP*42>A vacant slot number (no setting data)is set as the Alt.Feeder.

Remedy: <XP*42>Specify a slot number with a same part number.

------------------------------

Code: 2307903C

Display: Slot number is not defined.

Used by:

Cause: <XP*42>Slot number is not defined.

Remedy: <XP*42>Input the Slot number.

------------------------------

Code: 2307904A

Display: The Alt.Feeder function is not looping.

Used by:

Cause: <XP*42>An Alt.Feeder setting which includes two different stages is not suitable for the loop type

setting.

Remedy: <XP*42>Change the setting so that the Alt.Feeder setting has the same stage-slot number.

------------------------------

Code: 2307904B

Display: The Alt.Feeder is outside the permitted range.

Used by:

Cause: <XP*42>The Alt.Feeder input is outside the permitted range.The designated slot number does not

exist.

Remedy: <XP*42>Enter an Alt.Feeder within the permitted range.

------------------------------

Code: 23079828

Display: The Alt丏Feeder must be set to a separate feeder.

Used by:

Cause: <XP*42>The Slot Number and Alt丏Feeder are identical.

Remedy: <XP*42>Specify a Alt丏Feeder which is different from the slot number.

------------------------------

Code: 2307A10C

Display: Unregistered Packaging Type.A feeder cannot be selected.

Used by:

Cause: <XP*42>Cannot optimize because feeder width is unknown.A registered Packaging Type must be

used so that a feeder can be selected.

第 2172 页