FUJI错误代码查询.pdf - 第891页
------------------------------ Code: 1220003e Display: Servo amplifier error. Used by: Cause: Encoder feedback error. Information from the encoder is abnormal. Remedy: Check for breaks in the encoder wiring, or for bad c…
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
------------------------------
Code: 12200038
Display: Servo amplifier error.
Used by:
Cause: Undervoltage. The base DC voltage is too low.
Remedy: The power supply voltage could be fluctuating. Check the voltage.
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
------------------------------
Code: 12200039
Display: Servo amplifier error.
Used by:
Cause: Acceleration rate. The motor is rotating abnormally high.
Remedy: The speed setting could be abnormally high. Check the parameter settings.
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
------------------------------
Code: 1220003a
Display: Servo amplifier error.
Used by:
Cause: Momentary maximum torque. Operation was performed for several seconds at significantly over
the rated torque.
Remedy: Check to ensure that there is no interference or that the axis movement is not impeded. In
addition, check to ensure that none of the motor power lines are broken (U,V,W), or that there are no
shorts.
------------------------------
Code: 1220003b
Display: Servo amplifier error.
Used by:
Cause: DB overload. During dynamic braking, the rotational energy is more than the DB resistance
capacity.
Remedy: The emergency stop process could be incorrect. If this occurs frequently, replace Servo amplifier
with a new one.
------------------------------
Code: 1220003c
Display: Servo amplifier error.
Used by:
Cause: Initial resistance overload. The base power has been repeatedly turned on and off.
Remedy: Check for a short in the power line, or if the wire is broken, when this condition occurs.
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
------------------------------
Code: 1220003d
Display: Servo amplifier error.
Used by:
Cause: Heat sink is too hot. The heat sink for the servo pack is too hot.
Remedy: Check for abnormalities in the base circuitry or in the wiring for the motor power.
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
第 890 页
------------------------------
Code: 1220003e
Display: Servo amplifier error.
Used by:
Cause: Encoder feedback error. Information from the encoder is abnormal.
Remedy: Check for breaks in the encoder wiring, or for bad connections.
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
------------------------------
Code: 1220003f
Display: Servo amplifier error.
Used by:
Cause: Erratic movement detected. Motor was out of control.
Remedy: Check the base circuit wiring, motor power wiring, and encoder wiring for any abnormalities.
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
------------------------------
Code: 12200040
Display: Servo amplifier error.
Used by:
Cause: Positioning deviation is too large. Positioning deviation pulse was over the set value.
Remedy: Check to ensure that the deviation setting is appropriate.
Investigate the reason for it being out of control.
------------------------------
Code: 12200041
Display: Servo amplifier error.
Used by:
Cause: Power out of phase. One of the three phases for the power is not connected.
Remedy: Check to ensure that all wires for the three phases are not broken, or have any shorts.
------------------------------
Code: 12200042
Display: Servo amplifier error.
Used by:
Cause: Watch dog error. Abnormal SERCOS communication has occurred.
Remedy: Check to ensure that the digital operator is not connected.
Replace SERCOS unit with a new one if this occurs frequently, because the SERCOS unit could be
damaged.
------------------------------
Code: 12200043
Display: Servo amplifier error.
Used by:
Cause: MST, MDT error. SERCOS communication is abnormal.
Remedy: Check the fiber optic connections and make sure the digital operator is not connected.
Replace SERCOS board with a new one if no abnormalities are found, because the SERCOS board
could be damaged.
------------------------------
Code: 12200044
Display: Boot timeout.
Used by:
Cause: RTX Servo filter execution file is timeout of boot.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
第 891 页
------------------------------
Code: 12200045
Display: The magnetic pole detection failure.
Used by:
Cause: The execution of the Detected Magnet Pole is timeout.
Remedy: Check to ensure that the linear motor axis is no interference or that the axis movement is not
impeded.
------------------------------
Code: 12200046
Display: Program error.
Used by:
Cause: The specified function is effective only with the linear motor.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12200047
Display: The magnetic pole detection failure.
Used by:
Cause: It has executed magnetic pole detection.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12200048
Display: Program error.
Used by:
Cause: An indicated axis is registered on the other operation control at present.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12200049
Display: System error.
Used by:
Cause: The fault which it is impossible to recover occurs.
Remedy: This error is impossible to detect.
There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 1220004A
Display: Coordinate motion error.
Used by:
Cause: The draw time of the specified diagram is too long.
Remedy: Check the diagram information.If no abnormalities are found, and get a trace file.
------------------------------
Code: 1220004B
Display: Profile error.
Used by:
Cause: The profile could not be made as specified.
Remedy: Check to ensure that there is no interference or that the axis movement is not impeded.
------------------------------
Code: 1220004C
Display: Coordinate motion error.
Used by:
Cause: The coodinate motion of the specified handle isn't declarative in the use.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
第 892 页