FUJI错误代码查询.pdf - 第575页

making contact with the board or the PPC. ------------------------------ Code: 12056008 Display: Certify to B_mark Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643 Cause: The B-marks that the machine read are …

with a specific nozzle, inspect the nozzle detection locations for the specified head.

------------------------------

Code: 12056003

Display: 侧夹紧传感器逻辑异常

Used by: GSP5,GP551,GP6,GPX,GPX-C

Cause: 侧松开传感器或侧夹紧正常传感器的输入在逻辑上变得不正常。(GSP5) 即使电路板松开，侧夹紧落空确认传

感器也没有ON。 (GPX)

Remedy: 请进行侧松开传感器或侧夹紧正常传感器的调整／更换，使之变成以下的逻辑。

电路板松开时正常夹紧时夹紧失败时

松开 ○ × ×

正常夹紧 ○ ○ ×（GSP5）１．请确认是否有妨碍了侧夹紧动作的落下电路板等的

存在。

２．什么也没有时，需要进行电路板侧夹紧落空确认传感器(GPX:RX006,GPX-C:IN10)的调整。（请与本公司的

Support联系）（GPX,GPX-C)

------------------------------

Code: 12056004

Display: Sldr unit Position Error

Used by: GSP5

Cause: The position of the automatic paste dispenser is unacceptable.

Remedy: The adjustment of the sensor is probably incorrect. Adjust the sensor so that it corresponds

with the position of the automatic paste dispenser.

------------------------------

Code: 12056005

Display: Wrong Sqg Pres Data

Used by: GSP5

Cause: This error occurs only when the print pressure feedback option is in use.When measuring the

print pressure, a Low signal which was higher than the Hi signal was detected. This indicates that there

is an error in the Hi/Low logic specified in the print comparator. Furthermore, the low signal (X072 SQG

PRES LO) may be short circuited to GB.

Remedy: The print pressure input logic must be specified in the following manner: Hi is greater than

Low.Check that the high/low wiring is correct (GSP5). The pressure change/time gradient is too

steep.Adjust the Pressure/Time control item in Proper data to give a less steep gradient.

------------------------------

Code: 12056006

Display: M/C err Sqg Pres Range Over

Used by: GSP5,GP2,GP3,GP551,GP6

Cause: This error occurs only when print pressure feedback is being used. Although the control pressure

dropped below 0% or exceeded 100% when print pressure feedback was being used, the print pressure did

not automatically return to the specified range.

Remedy: The print pressure input logic must be specified in the following manner: Hi is greater than

Low.The printing height may be too low or there may be something between the screen and the board

(GSP5).

------------------------------

Code: 12056007

Display: Error : PPC origin positon sensor

Used by: IP3

Cause: During calibration the reference position check sensor did not come on when parts were being

placed, or the sensor was already on when operation began.

Remedy: At the I/O map check that the reference position check sensor turns on and off

correctly.Furthermore, check the sensor and the nozzle if the sensor is on even when the nozzle is not

第 574 页

making contact with the board or the PPC.

------------------------------

Code: 12056008

Display: Certify to B_mark

Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643

Cause: The B-marks that the machine read are all considered as "skip".

Remedy: Ensure that the B-marks are in the specified position of the program. After restarting the

machine, the B-marks arereread. Press the unload button to unload the board.

------------------------------

Code: 12056009

Display: "Pal Transport Err On R.Conv"

Used by: CP652C

Cause: The rear conveyor pallet arrival sensor has failed to indicate the arrival of a pallet within the

specified time.

Remedy: Make sure that the pallet is not stuck on the rear conveyor, and that nothing is obstructing

pallet movement.If there is no obstruction, perform an I/O check on the pallet arrival check sensor

(X09E), and adjust the sensor as necessary.

------------------------------

Code: 1205600A

Display: "Cleaner sensor logical alarm"

Used by: GP6

Cause: There is a logic error in input from the cleaner position check sensors.

Remedy: The logic error is in the following sensors: X05C:CLNR ZERO POS, X03E:CLNR NEAR CHK, and

X07C:CLNR SHIFT RET.In the case of a double-side cleaner, these three sensors should never all turn on

at once. The error may be caused by a wiring error or a sensor malfunction. Check the sensors and adjust

as necessary.

------------------------------

Code: 1205600B

Display: "Sensor logical alarm: upper cleaner head" (GP6)

Used by: GP6

Cause: The upper cleaner head open limit (X07C) and close limit (X07D) sensors have either both turned

on or both turned off at the same time.

Remedy: Check the upper cleaner head open limit and close limit sensors, and adjust them as necessary.

------------------------------

Code: 1205600C

Display: "Sensor logical alarm: lower cleaner head" (GP6)

Used by: GP6

Cause: The lower cleaner head open limit (X05A) and close limit (X05B) sensors have either both turned

on or both turned off at the same time.

Remedy: Check the lower cleaner head open limit and close limit sensors, and adjust them as necessary.

------------------------------

Code: 1205600D

Display: "Sensor logical alarm: cleaner notch" (GP6)

Used by: GP6

Cause: The cleaner notch sensors (X05D and X05E) sensors have either both turned on or both turned

off at the same time.

Remedy: If the machine supports a double-side cleaner, check and adjust the sensors for the notch that

connects the cleaner to the S-axis. If the machine uses a single-side cleaner, check and adjustthe sensors

for the notch that connects the cleaner to the cleaner shift.

------------------------------

Code: 1205600E

第 575 页

Display: "Sensor logical alarm: cleaner shift" (GP6)

Used by: GP6

Cause: The cleaner shift forward end (X07C) and retract end (X07D) sensors have either both turned on

or both turned off at the same time.

Remedy: Check the cleaner shift forward end and retract end sensors, and adjust them as necessary.

------------------------------

Code: 1205600F

Display: "M/C err Sensor SQG Holder" (GP6 w/single squeegee), "M/C err Sensor

SQG F" (front squeegee on double-squeegee GP6), "M/C err Sensor SQG R"

(rear squeegee on double-squeegee GP6)

Used by: GP6

Cause: The squeegee holder upper limit and lower limit check sensors (X070 and X071 for either a single

squeegee or squeegee F, and X078 and X079 for squeegee R) have either both turned on or both turned off

at the same time.

Remedy: Check the squeegee holder upper limit and lower limit check sensors, and adjust them as

necessary.

------------------------------

Code: 12056010

Display: "M/C err Sensor Top Cleaner Connected"

Used by: GP551

Cause: The opposite sensor has not turned off even though the cylinder has reached the destination

indicated by its output.

Remedy: Adjust the sensor.

------------------------------

Code: 12056011

Display: "Sensor Logic Error Conveyor Width Clutch"

Used by: GP551,GP6

Cause: The opposite sensor has not turned off even though the cylinder has reached the destination

indicated by its output.

Remedy: Adjust the sensor.

------------------------------

Code: 12056012

Display: "Sensor Logic Error Push Plate"

Used by: GP551,GP6

Cause: The opposite sensor has not turned off even though the cylinder has reached the destination

indicated by its output.

Remedy: Adjust the sensor.

------------------------------

Code: 12056013

Display: "M/C err Sensor Holder **(UPorDOWN)"

Used by: GP551

Cause: The opposite sensor has not turned off even though the cylinder has reached the destination

indicated by its output.

Remedy: Adjust the sensor.

------------------------------

Code: 12056014

Display: "Sensor Logic Error SQG Open/Close"

Used by: GP551,GP6

Cause: The opposite sensor has not turned off even though the cylinder has reached the destination

indicated by its output.

Remedy: Adjust the sensor.

第 576 页