FUJI错误代码查询.pdf - 第1787页

Used by: Cause: A range error occurred during vision processing, and the processing was cancelled. Remedy: A range error occurs when a check is performed on a part but the check point is not on the image. This could be c…

------------------------------

Code: 1D66F???

Display:

Used by:

Cause: There was a logical error in the management program.

Remedy: Check Part data.

------------------------------

Code: 1D670001

Display:

Used by:

Cause: A range error occurred during vision processing.

Remedy: A range error occurs when a check is performed on a part but the check point is not on the

image. This could be caused by

1) a large part being picked incorrectly, resulting in an incomplete image;

2) an incorrect CCD level setting or broken nozzle, resulting in a bad image;

3) an incorrect value entered in Part data (PDG) so that vision processing could not be done;

4) the Proper values CCD_X and CCD_Y are incorrect, resulting in a bad image;

5) a problem with the vision processing system program. Check the above listed conditions.

------------------------------

Code: 1D670002

Display:

Used by:

Cause: The part could not be found.

Remedy: Check the condition of the part feeding system. Check the CCD level and the nozzle sizes

entered in Proper data. When using a 1608 part S nozzle (1.00 mm) check whether or not the normal size

(1.3 mm) is entered. If this is the case and a 1608 part is picked, vision processing might register this as

not a part. If the CCD level is too high, the image will be too dark, and vision processing might register

this as not a part.

------------------------------

Code: 1D670006

Display:

Used by:

Cause: The part was tilted more than 45 deg. and processing was therefore cancelled.

Remedy: Check that the picking conditions have not gone bad.

------------------------------

Code: 1D670007

Display:

Used by:

Cause: A range error occurred during vision processing.

Remedy: None.

------------------------------

Code: 1D670008

Display:

Used by:

Cause: The lead information in Part data (PDG) was checked, and there are not more than two leads on

the appropriate side.

Remedy: Check the following items in PDG: number of leads, lead information and the orientation of the

parts on the feeder.

------------------------------

Code: 1D670009

Display:

第 1786 页

Used by:

Cause: A range error occurred during vision processing, and the processing was cancelled.

Remedy: A range error occurs when a check is performed on a part but the check point is not on the

image. This could be caused by

1) a large part being picked incorrectly, resulting in an incomplete image;

2) an incorrect CCD level setting or broken nozzle, resulting in a bad image;

3) an incorrect value entered in Part data (PDG) so that vision processing could not be done;

4) the Proper values CCD_X and CCD_Y are incorrect, resulting in a bad image;

5) a problem with the vision processing system program. Check the above listed conditions.

------------------------------

Code: 1D67000A

Display: 0010

Used by:

Cause: A range error occurred during vision processing, and the processing was cancelled.

Remedy: A range error occurs when a check is performed on a part but the check point is not on the

image. This could be caused by

1) a large part being picked incorrectly, resulting in an incomplete image;

2) an incorrect CCD level setting or broken nozzle, resulting in a bad image;

3) an incorrect value entered in Part data (PDG) so that vision processing could not be done;

4) the Proper values CCD_X and CCD_Y are incorrect, resulting in a bad image;

5) a problem with the vision processing system program. Check the above listed conditions.

------------------------------

Code: 1D67000B

Display: 0011

Used by:

Cause: The first lead could not be found during vision processing. A range error occurred during vision

processing, and the processing was cancelled.

Remedy: A range error occurs when a check is performed on a part but the check point is not on the

image. This could be caused by

1) a large part being picked incorrectly, resulting in an incomplete image;

2) an incorrect CCD level setting or broken nozzle, resulting in a bad image;

3) an incorrect value entered in Part data (PDG) so that vision processing could not be done;

4) the Proper values CCD_X and CCD_Y are incorrect, resulting in a bad image;

5) a problem with the vision processing system program. Check the above listed conditions.

------------------------------

Code: 1D67000C

Display: 0012

Used by:

Cause: The first lead could not be found during vision processing.

Remedy: Check that the part pickup conditions were OK.

------------------------------

Code: 1D67000D

Display: 0013

Used by:

Cause: Either the bright space exceeded the lead pitch by 50% or the dark space exceeded the lead width

by 50%. The dark space represents the actual lead width.

Remedy: Check the entries in Part data (PDG) for lead width, lead pitch and check the CCD level.

------------------------------

Code: 1D67000E

Display: 0014

Used by:

第 1787 页

Cause: The calculations of the lead locations on a leadless IC resulted in a range error.

Remedy: Calculate the leadless part at the PDG pitch item. Check the PDG lead pitch, lead information,

direction, and the orientation in which the parts are set on the machine.

------------------------------

Code: 1D67000F

Display: 0015

Used by:

Cause: Either the bright space exceeded the lead pitch by 50% or the dark space exceeded the lead width

by 50%. The dark space represents the actual lead width.

Remedy: Check the entries in Part data (PDG) for lead width, lead pitch and check the CCD level. The

Pitch limit item is entered in percentage points. An entry of 0 will give a default of 30%.

------------------------------

Code: 1D670010

Display: 0016

Used by:

Cause: The first lead could not be found during vision processing. A range error occurred during vision

processing, and the processing was cancelled.

Remedy: A range error occurs when a check is performed on a part but the check point is not on the

image. This could be caused by

1) a large part being picked incorrectly, resulting in an incomplete image;

2) an incorrect CCD level setting or broken nozzle, resulting in a bad image;

3) an incorrect value entered in Part data (PDG) so that vision processing could not be done;

4) the Proper values CCD_X and CCD_Y are incorrect, resulting in a bad image;

5) a problem with the vision processing system program. Check the above listed conditions.

------------------------------

Code: 1D670011

Display: 0017

Used by:

Cause: A range error occurred while checking for the ends of the leads.

Remedy: Check the Part data (PDG) lead length, pickup point, and the vision processing conditions.

------------------------------

Code: 1D670012

Display: 0018

Used by:

Cause: The part was moved to where under 60% of the body width has no leads and a range error

occurred.

Remedy: None.

------------------------------

Code: 1D670016

Display: 0022

Used by:

Cause: The machine decides whether or not there are leads on the part. The machine checked half the

part and found no leads, and this error occurred. Alternately, when a bright area is searched for after a

lead, no bright area is found for more than half the part.

Remedy: Check the body size and direction in Part data (PDG).

------------------------------

Code: 1D670017

Display: 0023

Used by:

Cause: When the bumper was recognized the leads were searched for from the center and a range error

occurred.

第 1788 页