FUJI错误代码查询.pdf - 第1120页

Display: In-carrier clamp limit and unclamp limit sensor logic error. Used by: CP-732E, CP-742ME, CP-742E Cause: In-carrier clamp limit and unclamp limit sensor logic error. Remedy: Verify that all sensors (X0B7 to X0BE)…

100%1 / 5282
Code: 1504022D
Display: In-carrier cycle error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: The in-carrier advance limit sensor failed to switch on. The in-carrier was retracted but the
retract limit sensor failed to switch on within the prescribed time period (8 secs.).
Remedy: Check to see if the in-carrier is operating smoothly. If operation is smooth, but the error still
occurs, check to see if the sensors (X0B3, X0B4) are operating properly.
------------------------------
Code: 1504022E
Display: In-carrier panel conveyance error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: After conveying the panel to the advance limit position with the panel being confirmed by the in-
carrier 1 panel sensor and the in-carrier 2 panel sensor, these sensors both switched off before the panel
could be loaded from the in-carrier to the in-lifter, resulting in a panel absent condition on the in-carrier.
In systems with an in-carrier panel present memory, the panel present/absent status on the in-carrier
was checked, but the in-carrier 1 panel sensor and the in-carrier 2 panel sensor could not verify the
presence of a panel .
Remedy: Check the panel conveyance condition. If there is no panel on the in-carrier, use the in-carrier
unclamp command to open the in-carrier. If this error occurs even though panel s are being conveyed
properly, check to see if the sensors (X0B1, X0B2) are operating properly.
------------------------------
Code: 1504022F
Display: In-carrier panel conveyance error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: At the in-carrier panel check, the in-carrier 1 panel sensor (X0B1) and the in-carrier 2 panel
sensor (X0B2) both switched on.
Remedy: Check the panel conveyance condition. If this error occurs even though the panel s are being
conveyed properly, check to see if the sensors (X0B1, X0B2) are operating properly.
------------------------------
Code: 15040230
Display: In-lifter panel conveyance error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: After panel loading to the in-lifter from the in-carrier began, the in-conveyor 1 panel arrival
sensor or the in-conveyor 2 panel arrival sensor switched from on to off before the in-carrier could be
advanced.
Remedy: Check the panel conveyance condition. If this error occurs even though panel s are being
conveyed properly, check to see if the sensors (X0AC, X0AE) are operating properly.
------------------------------
Code: 15040231
Display: In-carrier unclamp limit sensor input error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: In-carrier unclamp limit sensor input error.
Remedy: Verify that the sensors (X0B7 to X0BA) are operating properly.
------------------------------
Code: 15040232
Display: In-carrier clamp limit sensor input error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: In-carrier clamp limit sensor input error.
Remedy: Verify that the sensors (X0BB to X0BE) are operating properly.
------------------------------
Code: 15040233
第 1119 页
Display: In-carrier clamp limit and unclamp limit sensor logic error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: In-carrier clamp limit and unclamp limit sensor logic error.
Remedy: Verify that all sensors (X0B7 to X0BE) are operating properly.
------------------------------
Code: 15040234
Display: IN 1 stopper error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: The IN 1 stopper ON sensor failed to switch on. Although the IN 1 stopper was switched off, the
OFF limit sensor failed to switch on within the prescribed period of time (3 secs.).
Remedy: Check to see if the stopper is operating smoothly. If operation is smooth, but the error occurs
anyway, check to see if the sensors (X0C1, X0C2) are operating properly.
------------------------------
Code: 15040235
Display: In-conveyor panel set error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: When the in-conveyor 1 stopper was raised, the in-conveyor 1 panel arrival sensor switched from
on to off.
Remedy: Check the panel conveyance condition. The first panel which is already on the in-conveyor may
have been pushed upward out of position.
------------------------------
Code: 15040236
Display: In-conveyor panel conveyance error
Used by: CP-752E
Cause: The panel passed through the in-conveyor panel speed reduction sensor (X0AB) however, it was
not detected by the panel
arrival check sensor (X0AC) within the specified time limit.
Remedy: Check that the in-conveyor panel arrival check sensor is functioning properly and confirm the
panel status.
------------------------------
Code: 15040237
Display: In-conveyor panel conveyance error
Used by: CP-752E
Cause: An attempt was made to transfer the panel from the in-conveyor to the main-conveyor however,
the in-conveyor panel spee
d reduction sensor (X0AB) or the panel arrival check sensor (X0AC) did not deactivate (OFF) within the
specified time limit.
Remedy: Check that the in-conveyor panel speed reduction and panel arrival check sensors are
functioning properly and confirm t
he panel status.
------------------------------
Code: 15040238
Display: In-conveyor Stopper Error
Used by: CP-752E
Cause: One of the following errors has occurred:
The machine output the "lower stopper" signal, however the stopper lower end sensor (X0C2) did not
activate (ON).
oth the in-conveyor stopper upper end sensor (X0C1) and the in-conveyor stopper lower end sensor (X0C2)
did not activate (ON) wi
thin the specified time limit.
Both the in-conveyor stopper upper end sensor (X0C1) and the in-conveyor stopper lower end sensor
第 1120 页
(X0C2) did not deactivate (OFF
) within the specified time limit.
Remedy: Check that the stopper is functioning properly. If the error continues, check that both of the
sensors带幨X0C1, X0C2带幩ar
e functioning properly.
------------------------------
Code: 15040239
Display: In-conveyor panel conveyance error
Used by: CP-752E
Cause: The in-conveyor panel arrival sensor (X0AC) was activated (ON) before the panel speed reduction
sensor (X0AB).
Remedy: Check that the in-conveyor panel speed reduction sensor is functioning properly and confirm the
panel status.
------------------------------
Code: 1504023A
Display: 电路板位置异常 载入侧搬运轨道
Used by: GPX,NXTP
Cause: 在载入侧搬运轨道无法搬运的位置上有电路板。
Remedy: 请除去电路板然后重新放入。
<img src="$LKEY_ERRIMG_MC$/EI0001.bmp">
------------------------------
Code: 1504023B
Display: 载入搬运轨道有电路板错误
Used by: NXTP
Cause: 因为在载入搬运轨道上有电路板，所以不进入到下一步的处理。
Remedy: 请清除电路板。
<img src="$LKEY_ERRIMG_MC$/1504023B.PNG">
------------------------------
Code: 1504023C
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 1504023D
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 1504023E
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 1504023F
Display:
Used by:
Cause:
Remedy:
第 1121 页