FUJI错误代码查询.pdf - 第212页

Code: 11081042 Display: Overtravel: Check X- Axis Used by: MTU3,MTU4,MTU5 Cause: The X axis - overtravel sensor is on, or the software limit has been exceeded. Remedy: Move the X axis to a point before the overtravel sen…

Code: 11081031

Display: Part Carrier Cycle alarm

Used by: MTU4

Cause: When the parts supply carrier advances or retracts, the advance end and retract end sensors do

not come on.

Remedy: Check that the position of the sensors has not shifted. Check that there are no anomalies in the

carrier drive motor and actuator. Power may not be supplied to the carrier drive motor controller. In that

case switch on the power.

------------------------------

Code: 11081032

Display: T Axis Cycle alarm

Used by: MTU4

Cause: When the T axis (the tray) moved it did not reach its target position.

Remedy: Check that there are no problems in the T axis servo system and that the various connectors are

correctly connected.

------------------------------

Code: 11081033

Display: X Axis Cycle alarm

Used by: MTU3,MTU4,MTU5

Cause: When the X axis moved it did not reach its target position.

Remedy: Check that there are no problems in the X axis servo system and that the various connectors are

correctly connected.

------------------------------

Code: 11081034

Display: Y Axis Cycle alarm

Used by: MTU3,MTU4,MTU5

Cause: When the Y axis moved it did not reach its target position.

Remedy: Check that there are no problems in the Y axis servo system and that the various connectors are

correctly connected.

------------------------------

Code: 11081035

Display: Z Axis Cycle alarm

Used by: MTU3,MTU4,MTU5

Cause: When the Z axis moved it did not reach its target position.

Remedy: Check that there are no problems in the Z axis servo system and that the various connectors are

correctly connected.

------------------------------

Code: 11081036

Display: Parts Conveyor Cycle alarm

Used by: MTU3,MTU5

Cause: When the parts conveyor axis moved it did not reach its target position.

Remedy: Check that there are no problems in the parts conveyor axis servo system and that the various

connectors are correctly connected.

------------------------------

Code: 11081041

Display: Overtravel: Check X+ Axis

Used by:

Cause: The X axis + overtravel sensor is on, or the software limit has been exceeded.

Remedy: Move the X axis to a point before the overtravel sensor or to a point inside the position set in the

Proper data item max_limit_sx.

------------------------------

第 211 页

Code: 11081042

Display: Overtravel: Check X- Axis

Used by: MTU3,MTU4,MTU5

Cause: The X axis - overtravel sensor is on, or the software limit has been exceeded.

Remedy: Move the X axis to a point before the overtravel sensor or to a point inside the position set in the

Proper data item min_limit_sx.

------------------------------

Code: 11081043

Display: Overtravel: Check Y+ Axis

Used by: MTU3,MTU4,MTU5

Cause: The Y axis + overtravel sensor is on, or the software limit has been exceeded.

Remedy: Move the Y axis to a point before the overtravel sensor or to a point inside the position set in the

Proper data item max_limit_sy.

------------------------------

Code: 11081044

Display: Overtravel: Check Y- Axis

Used by: MTU3,MTU4,MTU5

Cause: The Y axis - overtravel sensor is on, or the software limit has been exceeded.

Remedy: Move the Y axis to a point before the overtravel sensor or to a point inside the position set in the

Proper data item min_limit_sy.

------------------------------

Code: 11081045

Display: Overtravel: Check Z+ Axis

Used by: MTU3,MTU4,MTU5

Cause: The Z axis + overtravel sensor is on, or the software limit has been exceeded.

Remedy: Move the Z axis to a point before the overtravel sensor or to a point inside the position set in the

Proper data item max_limit_sz.

------------------------------

Code: 11081046

Display: Overtravel: Check Z- Axis

Used by: MTU3,MTU4,MTU5

Cause: The Z axis - overtravel sensor is on, or the software limit has been exceeded.

Remedy: Move the Z axis to a point before the overtravel sensor or to a point inside the position set in the

Proper data item min_limit_sz.

------------------------------

Code: 11081047

Display: Overtravel: Check T+ Axis

Used by: MTU4

Cause: The T axis + overtravel sensor is on, or the software limit has been exceeded.

Remedy: Move the T axis to a point before the overtravel sensor or to a point inside the position set in the

Proper data item max_limit_t.

------------------------------

Code: 11081048

Display: Overtravel: Check T- Axis

Used by: MTU4

Cause: The T axis - overtravel sensor is on, or the software limit has been exceeded.

Remedy: Move the T axis to a point before the overtravel sensor or to a point inside the position set in the

Proper data item min_limit_t.

------------------------------

Code: 11081049

Display: Software limit: Check X

第 212 页

Used by: MTU3,MTU4,MTU5

Cause: The X axis is outside the software limit set in the MTU Proper data.

Remedy: Move the X axis to within the software limit and check that the values set in Proper data agree.

------------------------------

Code: 1108104A

Display: Software limit: Check Y

Used by: MTU3,MTU4,MTU5

Cause: The Y axis is outside the software limit set in the MTU Proper data.

Remedy: Move the Y axis to within the software limit and check that the values set in Proper data agree.

------------------------------

Code: 1108104B

Display: Software limit: Check Z

Used by: MTU3,MTU4,MTU5

Cause: The Z axis is outside the software limit set in the MTU Proper data.

Remedy: Move the Z axis to within the software limit and check that the values set in Proper data agree.

------------------------------

Code: 1108104C

Display: Software limit: Check T

Used by: MTU4

Cause: The T axis is outside the software limit set in the MTU Proper data.

Remedy: Move the T axis to within the software limit and check that the values set in Proper data agree.

------------------------------

Code: 11081060

Display: 11081060

Used by: MTU3,MTU4,MTU5

Cause: The sub-robot moved into the interference range defined by the MTU Proper data.

Remedy: Check the MTU Proper data (tray origin point, interlock etc).

------------------------------

Code: 11081061

Display: REDUCE SY Sensor Went Off During T Axis Movement

Used by: MTU4

Cause: The Y axis speed reduction sensor was off while the T axis was moving.

Remedy: Check the Y axis speed reduction sensor and the dog.

------------------------------

Code: 11081062

Display: TRAY SPACE OK Sensor Went Off During SY Axis Movement

Used by: MTU4

Cause: The T axis robot safety sensor was off while the SY axis was moving.

Remedy: Check the T axis robot safety sensor and the dog on the tray which caused the error.

------------------------------

Code: 11081063

Display: SZ READY Sensor Went Off During SY Axis Movement

Used by: MTU4

Cause: The Z axis interlock sensor was off while the Y axis was moving.

Remedy: Check the Z axis interlock sensor and the dog.

------------------------------

Code: 11081070

Display: Air Pressure Alarm

Used by: MTU3,MTU4,MTU5

Cause: The air pressure sensor detected a drop in the air pressure.

Remedy: Check that air is being supplied and that the air pressure is not falling. Furthermore, if the

第 213 页