FUJI错误代码查询.pdf - 第514页

Display: Scan area error Used by: NP2,QP3 Cause: Either the scan area exceeds 81.92mm in both the X and Y directions, or the frame size exceeds 4MB. Remedy: Specify a scan area which is suitable for the size of the part …

Code: 1205040A

Display: Pallet system error

Used by: CP5

Cause: The pallet control software is defective.

Remedy: Contact Fuji.

------------------------------

Code: 1205040B

Display: 存在着无法读取定位点的顺序

[Mark seq. not processed]

Used by: GP2,GP3,IP3,QP132,GPX,NXTP

Cause: 读取BadMark的时候，或者，没有读取在贴装元件时参照的基准定位点。没有发现钢板的定位点。 (GPX)

Remedy: 发生在没有对应「自动重新读取定位点」的机型。请重新读取定位点。 1.请确认定位点是否弄脏。

2.请确认定位点形状或检索范围是否被正确设定了。（GPX)

------------------------------

Code: 1205040C

Display: ST2 Parts chk sensor err.

Used by: CP-IV/IV-2(SMD3), CPIV-3/6/6M/642/65/652C

Cause: There is a sensor error at station 2, large part check.

This could be caused by misalignment of the light beam in the sensor, a broken wire leading to the sensor

part that emits the beam, or the entire sensor itself may be malfunctioning.

Remedy: If there is a problem with the alignment of the light beam, adjust the beam. If there is a problem

with the part of the sensor that emits the light beam, after determining the cause of the error, replace the

sensor, rewire the sensor, etc.

Additionally, check station 2 to verify that a part has been picked up, and examine the device feeder.

------------------------------

Code: 12050410

Display: I/O system error!

Used by: NP2,QP3

Cause: An error occurred in the I/O system.

Remedy: Restart the machine.

------------------------------

Code: 12050411

Display: MFU Proper data writing error

Used by: NP2,QP3

Cause: MFU Proper data writing failed.

Remedy: This is a LON communication error. Restart the machine.

------------------------------

Code: 12050412

Display: MTU Proper data writing error

Used by: NP2,QP3

Cause: MTU Proper data writing failed.

Remedy: This is a LON communication error. Restart the machine.

------------------------------

Code: 12050413

Display: PFU Proper data writing error

Used by: NP2,QP3

Cause: PFU Proper data writing failed.

Remedy: This is a LON communication error. Restart the machine.

------------------------------

Code: 12050414

第 513 页

Display: Scan area error

Used by: NP2,QP3

Cause: Either the scan area exceeds 81.92mm in both the X and Y directions, or the frame size exceeds

4MB.

Remedy: Specify a scan area which is suitable for the size of the part in question. If the scan area is

specified as "0", the scan area is determined automatically.

------------------------------

Code: 12050420

Display: PFU docking error!

Used by: NP2,QP3

Cause: The PFU is not attached.

Remedy: Check if the PFU is correctly attached to the machine.

------------------------------

Code: 12050421

Display: Connection error for parts supply unit.

Used by: NP2,QP3

Cause: The input for the parts supply unit at the stage displayed in the parameter section switched off.

Remedy: Check if the parts supply unit has been correctly set.

------------------------------

Code: 12050422

Display: LON communication error!

Used by: NP2,QP3

Cause: LON communication error!

Remedy: Use the [Power On] command at the [Unit] command screen to turn the power to the parts

supply unit on.

------------------------------

Code: 12050423

Display: Nozzle settings error!

Used by: NP2,QP3

Cause: The required nozzle is not located in the position specified in nozzle settings.

Remedy: Check nozzle memory.

------------------------------

Code: 12050424

Display: Tray eject error!

Used by: NP2,QP3

Cause: The tray remover may be holding a tray.

Remedy: If the tray remover is holding a tray, remove tray. Alternatively turn the vacuum supply to the

tray remover off.

------------------------------

Code: 12050425

Display: MTU shuttle speed setting error

Used by: NP2,QP3

Cause: MTU slot information cannot be set.

Remedy: Re-specify the production program, then re-specify the MTU slot information.

------------------------------

Code: 12050426

Display: SOOP checking error!

Used by: QP301

Cause: A raised part was detected.

Remedy: Check the condition of the parts on the FOL carrier.

------------------------------

第 514 页

Code: 12050427

Display: Consecutive defective carrier error

Used by: QP301

Cause: The number of consecutive carriers for which an error was recorded has exceeded the specified

limit.

Remedy: Check the condition of the parts on the FOL carrier.

------------------------------

Code: 12050428

Display: Defective package count error

Used by: QP301

Cause: The number of packages for which an error was recorded has exceeded the specified limit.

Remedy: Check the condition of the parts on the FOL carrier.

------------------------------

Code: 12050429

Display: SOOP Data Collection Error!

Used by: QP301

Cause: A communication error occurred between the Machine and amp unit during the collection of

SOOP d ata.

Remedy: Cut the power to the machine and check the RS cable.

------------------------------

Code: 1205042A

Display: Temperature warning.

Used by: QP3

Cause: The heater temperature is outside the suitable range.

Remedy: Wait until the temperature settles.

------------------------------

Code: 1205042B

Display: Heater error.

Used by: QP3

Cause: The heater temperature is not correct. The temperature controller or sensor may be damaged.

Remedy: Cut the power to the machine and check the temperature controller and sensor.

------------------------------

Code: 1205042C

Display: Temperature warning.

Used by: QP3

Cause: Switching to single panel production as the heater temperature is outside the suitable range.

Remedy: Wait until the temperature settles, and then resume operation.

------------------------------

Code: 1205042D

Display: Temperature warning.

Used by: QP3

Cause: Cannot operate as the heater temperature is outside the suitable range.

Remedy: Start operation after the temperature has settled.

------------------------------

Code: 1205042E

Display: Pallet Setting Error

Used by: CP732E,CP742ME,CP742E,CP752E

Cause: Pallet clamping was unsuccessful.

Remedy: Check if the following sensor(s) is ON using I/O.

Stage1: X087 D1 PALLET SET CHECK FRONT

X088 D1 PALLET SET CHECK REAR

第 515 页