FUJI错误代码查询.pdf - 第892页
------------------------------ Code: 12200045 Display: The magnetic pole detection failure. Used by: Cause: The execution of the Detected Magnet Pole is timeout. Remedy: Check to ensure that the linear motor axis is no i…
------------------------------
Code: 1220003e
Display: Servo amplifier error.
Used by:
Cause: Encoder feedback error. Information from the encoder is abnormal.
Remedy: Check for breaks in the encoder wiring, or for bad connections.
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
------------------------------
Code: 1220003f
Display: Servo amplifier error.
Used by:
Cause: Erratic movement detected. Motor was out of control.
Remedy: Check the base circuit wiring, motor power wiring, and encoder wiring for any abnormalities.
Replace Servo amplifier with a new one if no abnormalities are found, because the servo amplifier
could be damaged.
------------------------------
Code: 12200040
Display: Servo amplifier error.
Used by:
Cause: Positioning deviation is too large. Positioning deviation pulse was over the set value.
Remedy: Check to ensure that the deviation setting is appropriate.
Investigate the reason for it being out of control.
------------------------------
Code: 12200041
Display: Servo amplifier error.
Used by:
Cause: Power out of phase. One of the three phases for the power is not connected.
Remedy: Check to ensure that all wires for the three phases are not broken, or have any shorts.
------------------------------
Code: 12200042
Display: Servo amplifier error.
Used by:
Cause: Watch dog error. Abnormal SERCOS communication has occurred.
Remedy: Check to ensure that the digital operator is not connected.
Replace SERCOS unit with a new one if this occurs frequently, because the SERCOS unit could be
damaged.
------------------------------
Code: 12200043
Display: Servo amplifier error.
Used by:
Cause: MST, MDT error. SERCOS communication is abnormal.
Remedy: Check the fiber optic connections and make sure the digital operator is not connected.
Replace SERCOS board with a new one if no abnormalities are found, because the SERCOS board
could be damaged.
------------------------------
Code: 12200044
Display: Boot timeout.
Used by:
Cause: RTX Servo filter execution file is timeout of boot.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
第 891 页
------------------------------
Code: 12200045
Display: The magnetic pole detection failure.
Used by:
Cause: The execution of the Detected Magnet Pole is timeout.
Remedy: Check to ensure that the linear motor axis is no interference or that the axis movement is not
impeded.
------------------------------
Code: 12200046
Display: Program error.
Used by:
Cause: The specified function is effective only with the linear motor.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12200047
Display: The magnetic pole detection failure.
Used by:
Cause: It has executed magnetic pole detection.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12200048
Display: Program error.
Used by:
Cause: An indicated axis is registered on the other operation control at present.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 12200049
Display: System error.
Used by:
Cause: The fault which it is impossible to recover occurs.
Remedy: This error is impossible to detect.
There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
Code: 1220004A
Display: Coordinate motion error.
Used by:
Cause: The draw time of the specified diagram is too long.
Remedy: Check the diagram information.If no abnormalities are found, and get a trace file.
------------------------------
Code: 1220004B
Display: Profile error.
Used by:
Cause: The profile could not be made as specified.
Remedy: Check to ensure that there is no interference or that the axis movement is not impeded.
------------------------------
Code: 1220004C
Display: Coordinate motion error.
Used by:
Cause: The coodinate motion of the specified handle isn't declarative in the use.
Remedy: There is possibility that version up isn't correct.Reinstall the recovery media software.
------------------------------
第 892 页
Code: 1220004D
Display: HOME sensor error.
Used by:
Cause: The HOME sensor is detected at the wrong timing in the homing.
Remedy: The noise may be mixed in the HOME sensor input terminal.
Please check the dirt of a HOME sensor light input part,
Please check that poor connection has not occurred between the SERVO board (amplifier) and a
HOME sensor.
------------------------------
Code: 12200050
Display: Board error.
Used by:
Cause: The servo board set in the servo initialization file is not supported.
Remedy: Check the setting in the servo initialization file, and that the servo control board is correct.
If no abnormalities are found, the board could be damaged.
------------------------------
Code: 12200051
Display: Failed to create object.
Used by:
Cause: Failed to create a servo object.
Remedy: Reinstall the software because the initial installation could have failed.
If this error is not corrected, the servo control board could be damaged.
------------------------------
Code: 12200052
Display: Abnormal ADC number.
Used by:
Cause: The ADC number setting does not exist.
Remedy: Check the value in the servo initialization file.
If no abnormalities are found, reinstall the software.
------------------------------
Code: 12200053
Display: Axis number is outside the valid range.
Used by:
Cause: An invalid value has been set in the parameter's argument (axis number).
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12200054
Display: Board number is outside the valid range.
Used by:
Cause: The setting for the servo controller board number is incorrect.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12200055
Display: Acceleration time is outside the valid range.
Used by:
Cause: The acceleration time setting is outside the valid range.
Remedy: Reinstall the software because the initial installation could have failed.
------------------------------
Code: 12200056
Display: Deceleration time is outside the valid range.
Used by:
第 893 页