FUJI错误代码查询.pdf - 第867页

is damaged. Remedy: If this error occurs only one time after upgrading, there is no problem. If this error occurs frequently, contact Fuji because the servo control board could be damaged. ------------------------------ …

100%1 / 5282
Code: 1211000c
Display: Process not ended.
Used by:
Cause: Processing was not completed. The system resources are insufficient, the operating system is
corrupted, or the operating system installation failed.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the hard disk could be damaged.
------------------------------
Code: 1211000d
Display: Missing RT process load.
Used by:
Cause: The required file is either corrupted or may have been deleted.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the hard disk could be damaged.
------------------------------
Code: 1211000e
Display: Failed to create object.
Used by:
Cause: Failed to create the servo driver control object, or the servo controller device driver file is
corrupted.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the servo control board could be damaged.
------------------------------
Code: 1211000f
Display: Firmware does not match.
Used by:
Cause: The version check performed after a servo control board firmware upgrade has found that the
version does not match.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the servo control board could be damaged.
------------------------------
Code: 12110011
Display: Failed to access the firmware.
Used by:
Cause: Failed to access the servo control firmware, or the servo controller device driver is corrupted.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the servo control board could be damaged.
------------------------------
Code: 12110012
Display: Firmware check error.
Used by:
Cause: An error was detected when performing a servo control firmware check, or the servo controller
device driver is corrupted.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the servo control board could be damaged.
------------------------------
Code: 12110013
Display: Firmware overwritten.
Used by:
Cause: The servo control firmware has been overwritten. This occurs for certain versions after
immediately upgrading. This error occurs frequently after booting up the machine when the flash memory
第 866 页
is damaged.
Remedy: If this error occurs only one time after upgrading, there is no problem. If this error occurs
frequently, contact Fuji because the servo control board could be damaged.
------------------------------
Code: 12110014
Display: Firmware error.
Used by:
Cause: The servo control firmware name is not specified.
It is possible that the servo initialization file is corrupted, an incorrect setting has been specified,
or the servo controller device driver is corrupted
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the hard disk could be damaged.
------------------------------
Code: 12110015
Display: Linear encoder.
Used by:
Cause: An unexpected error occurred while confirming the linear encoder connection, or the servo
controller device driver is corrupted.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the servo control board could be damaged.
------------------------------
Code: 12110016
Display: Linear encoder error.
Used by:
Cause: The linear encoder connection check detected an inappropriate encoder.
Some other encoder is connected to the axis with the linear encoder setting, or the dip switch
setting for the machine is incorrect.
Remedy: Check the connection for the linear encoder. Ensure that the dip switch and amplifier settings
are correct.
------------------------------
Code: 12110017
Display: Initialization failed.
Used by:
Cause: Failed to initialize servo controller access, or the servo controller device driver is corrupted.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the servo control board could be damaged.
------------------------------
Code: 12110018
Display: ABS encoder error.
Used by:
Cause: Failed to recognize the ABS encoder value. It is possible that the SEN signal was not sent
normally.
Remedy: Check all of the axes encoder wires, and that the SEN signal is connected properly.
If this cannot be corrected, contact Fuji, because it is possible that the amplifier is damaged.
------------------------------
Code: 12110019
Display: Abnormal SERCOS communication.
Used by:
Cause: An unidentified node is present in the SERCOS ring. An amplifier dip switch setting is incorrect,
or a servo initialization file setting is incorrect.
Remedy: Check the connections in the SERCOS ring, the amplifier dip switch and rotary switch settings,
第 867 页
and the servo initialization file settings.
------------------------------
Code: 1211001a
Display: Abnormal SERCOS communication.
Used by:
Cause: A node is missing from the SERCOS ring. An amplifier dip switch setting is incorrect, or a servo
initialization file setting is incorrect.
Remedy: Check the connections in the SERCOS ring, the amplifier dip switch and rotary switch settings,
and the servo initialization file settings.
------------------------------
Code: 1211001b
Display: Servo initialization file error.
Used by:
Cause: There is an inappropriate setting in the servo initialization file, or the displayed file is corrupted.
Remedy: After checking the settings, reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the hard disk could be damaged.
------------------------------
Code: 1211001c
Display: A setting is outside the valid range.
Used by:
Cause: A setting in the servo initialization file is outside the valid range, or the displayed file is corrupted.
Remedy: After checking the settings, reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the hard disk could be damaged.
------------------------------
Code: 1211001d
Display: Insufficient working memory.
Used by:
Cause: Either the system resources are insufficient, the operating system is corrupted, or the operating
system installation failed.
Remedy: Reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the hard disk could be damaged.
------------------------------
Code: 1211001e
Display: Parameter setting error.
Used by:
Cause: The sequence order of settings in the servo initialization file is incorrect, or the servo initialization
file is corrupted.
Remedy: After checking the settings, reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the hard disk could be damaged.
------------------------------
Code: 1211001f
Display: Parameter error.
Used by:
Cause: An incorrect parameter is set in the servo initialization file, or the servo initialization file is
corrupted.
Remedy: After checking the settings, reinstall the recovery media software.
Contact Fuji if this error cannot be corrected, because the hard disk could be damaged.
------------------------------
Code: 12110020
Display: Cannot access a file.
Used by:
第 868 页