FUJI错误代码查询.pdf - 第579页

Remedy: The sensor status must be as follows during part placement: Main-conveyor upper1 limit sensor (X064): OFF Main-conveyor lower limit sensor (X067): ON Main-conveyor middle overtravel sensor(X066): ON -------------…

100%1 / 5282
Display: "Sensor Logic Error Screen Transport Clamp"
Used by: GP6
Cause: The screen transport chuck open limit and close limit sensors (1111 and 1112) have either both
turned on or both turned off at the same time.
Remedy: Check the screen transport chuck open limit and close limit sensors, and adjust them as
necessary.
------------------------------
Code: 1205601D
Display: "Sensor Logic Error Screen Lifter"
Used by: GP6
Cause: The screen lifter upper limit and lower limit check sensors (1113 and 1114) have either both
turned on or both turned off at the same time.
Remedy: Check the screen lifter upper limit and lower limit check sensors, and adjust them as necessary.
------------------------------
Code: 1205601E
Display: "Sensor Logic Error Screen Pusher"
Used by: GP6
Cause: The screen pusher forward end and retract end check sensors (1113 and 1114) have either both
turned on or both turned off at the same time.
Remedy: Check the screen pusher forward end and retract end check sensors, and adjust them as
necessary.
------------------------------
Code: 1205601F
Display: Sensor Logic Error Camera/Lower Cleaner Pos
Used by: GP551
Cause: The origin position sensor and the proximity sensor for both the camera and lower cleaner are
simultaneously in the on condition, resulting in an error.
Remedy: Check the on/off status for the camera's retract position sensor, the lower cleaner's origin
position sensor, and the proximity sensors for both the lower cleaner and the camera.
------------------------------
Code: 12056020
Display: Sensor logic alarm Z-axis
Used by: GP551
Cause: An alarm occurred because the sensors which check that the movement of the Z-axis is in the
permissible range are not operating correctly.
Remedy: Check the operation of these sensors by ensuring the sensors behave in the following manner
when the Z-axis is moved from the loading position to the printing position.
(1) (2) (3)(4)
Y-axis interlock sensor ON OFF OFFOFF
Z-axis retract position sensor ON ON OFFOFF
Z-axis/lower cleaner interlock sensor ON ON ONOFF
(1) When the Z-axis is at the loading position.
(2) When the Z-axis is moved from the loading position to the mark read position.
(3) When the Z-axis is at the mark reading position.
(4) When the Z-axis is at the printing position.
------------------------------
Code: 12056021
Display: Lifter up1/down lmt snsr err
Used by: CP643
Cause: A logic error has occurred between the sensors that check table height
during part placement.
第 578 页
Remedy: The sensor status must be as follows during part placement:
Main-conveyor upper1 limit sensor (X064): OFF
Main-conveyor lower limit sensor (X067): ON
Main-conveyor middle overtravel sensor(X066): ON
------------------------------
Code: 12056026
Display: Nozzle change error
Used by: NP2,QP3
Cause: Machine stopped during a nozzle change.
Remedy: Use the nozzle edit panel to verify that the nozzle memory data is correct.
------------------------------
Code: 12056027
Display: MTU area sensor error
Used by: NP2,QP3
Cause: The MTU area sensor was interrupted during non-stop parts supply.
Remedy: Press the READY ON switch and resume operation if possible.
------------------------------
Code: 12056028
Display: Nozzle drop detection
Used by: NP2,QP3
Cause: Nozzle drop was detected.
Remedy: Ensure that a nozzle is set in the holder.
------------------------------
Code: 12056029
Display: Zero setting error
Used by: NP2,QP3
Cause: An attempt was made to perform zero setting during pick up.
Remedy: Reject the parts and then perform zero setting again.
------------------------------
Code: 1205602A
Display: 操作系统出错
Used by: XP141,XP241,XP341,XP142,XP242
Cause: 系统错误
Remedy: 请获取跟踪数据，并将它送至弊社。
------------------------------
Code: 1205602B
Display: 检查出吸嘴的浮起。请确认吸嘴的置放地。
Used by: XP241,XP341,XP242
Cause: 吸嘴浮起的确认传感器被遮光。
Remedy: 吸嘴没有浮起时请确认传感器的ON/OFF并进行调整。
------------------------------
Code: 1205602C
Display: 没有正确安装吸取器。请确认吸取器的置放地。
Used by: XP241,XP242
Cause: 吸取器置放地的传感器被遮光。
Remedy: 放置有吸取器时请确认传感器的ON/OFF并进行调整。
------------------------------
Code: 12056030
Display: 往复臂所钩住的料盘的号码不清楚。
不能收存料盘。
请用关闭错误画面后所显示的对话框来选择往复臂所钩住的料盘的料站号码。
第 579 页
Used by: XP241,XP242
Cause: 往复臂所钩住的料盘号码不清楚。
Remedy: 关闭错误画面后在显示的对话框上选择往复臂所钩住的料盘的料站号码。
------------------------------
Code: 12056031
Display: 真空吸取器与料盘定位板相干扰，所以不能排出料盘。
Used by: XP242
Cause: 吸取器与料盘定位板相干扰。
料盘X方向的长度(Tray Length)比吸取器小的料盘，在XP标准料盘盒上不能被排出。
Remedy: 请将元件数据的Tray Type变更为非自动排出型(4)，或使用高精度的料盘。
------------------------------
Code: 12056032
Display: 真空吸取器与料盘定位板相干扰，所以不能排出料盘。
Used by: XP242
Cause: 吸取器与料盘定位板相干扰。
料盘Y方向的长度 (Tray Width) 比吸取器小的料盘，在XP标准料盘盒上不能被排出。
Remedy: 请将元件数据的Tray Type变更为非自动排出型(4)，或使用高精度的料盘。
------------------------------
Code: 12056033
Display: 真空吸取器与料盘定位板相干扰，所以不能排出料盘。
请将料盘数据的Tray Dump Pick Position X值修正为料盘吸取器不超出料盘的值。
Used by: XP242
Cause: 吸取空料盘时吸取器与料盘定位板相干扰。
Remedy: 请将元件数据的Tray Dump Pick Position X修正为吸取器不超出料盘的值。
------------------------------
Code: 12056034
Display: 真空吸取器与料盘定位板相干扰，所以不能排出料盘。
请将料盘数据的Tray Dump Pick Position Y值修正为料盘吸取器不超出料盘的值。
Used by: XP242
Cause: 吸取空料盘时吸取器与料盘定位板相干扰。
Remedy: 请将元件数据的Tray Dump Pick Position X修正为吸取器不超出料盘的值。
------------------------------
Code: 12056035
Display: 吸嘴与料盘定位板相干扰，所以不能吸取元件。(从机器正面看是在自己面前)
Used by: XP242
Cause: 吸取元件时吸嘴与料盘定位板相干扰。(从机器正面看是在自己面前)
Remedy: 请变更元件数据的[Tray First Pickup Position Y]，或者当[Direction]为1、3时变更[Pick-up Point
Offset X]，当[Direction]为0、2时变更[Pick-up Point Offset Y]，修正为吸嘴与料盘定位板不相干扰的值。
------------------------------
Code: 12056036
Display: 吸嘴与料盘定位板相干扰，所以不能吸取元件。(从机器正面看是在右方)
Used by: XP242
Cause: 吸取元件时吸嘴与料盘定位板相干扰。(从机器正面看是在右侧)
Remedy: 请变更元件数据的[Tray First Pickup Position X]，或者当[Direction]为0、2时变更[Pick-up Point
Offset X]，当[Direction]为1、4时变更[Pick-up Point Offset Y]，修正为吸嘴与料盘定位板不相干扰的值。
------------------------------
Code: 12056037
Display: 吸嘴与料盘定位板相干扰，所以不能吸取元件。(从机器正面看是在左方)
Used by: XP242
Cause: 吸取元件时吸嘴与料盘定位板相干扰。(从机器正面看是在左侧)
Remedy: 请变更元件数据的[Tray First Pickup Position X], [Tray ColumnPitch],[Tray Column Quantity]，或者
第 580 页