FUJI错误代码查询.pdf - 第161页

------------------------------ Code: 11022704 Display: Used by: CP4-1,CP4-2,CP4- 3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GSP5,GP2,GP3,GP6,IP3,QP242,QP201,QP202,QP20 3,QP132 Cause: The Proper data item Reader port 2 …

100%1 / 5282
Code: 1102263F
Display: None
Used by: IP-3
Cause: Nozzle1_12 settings cannot be used when camera types 12 or 13 are fitted on the head 1 side of
the machine.
Remedy: Clear the settings for Nozzle1_12 and retransmit Proper data.
------------------------------
Code: 11022640
Display: None
Used by: IP-3
Cause: Nozzle2_12 settings cannot be used when camera types 12 or 13 are fitted on the head 2 side of
the machine.
Remedy: Clear the settings for Nozzle2_12 and retransmit Proper data.
------------------------------
Code: 11022701
Display: 11022701
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GSP5,GP2,GP3,GP6,IP2,IP3,QP242,QP201,QP202,Q
P203,QP132
Cause: The Proper data item Command_line_port is out of range (when using HELPS).
Remedy: Check the Proper data item Command_line_port, and retransmit Proper data. This Proper data
item specifies the number of the communication board or LCU connector to which the LMS command line
cable is connected. (the connector number is from 1-4 for machines and from 1-8 for peripherals). Do not
use the same port numbers for different operations. Avoid setting Command_line_port to 1 or 3 for
peripheral machines. Command_line_port is normally set to 2 (this is preset when the machine is
shipped.)
------------------------------
Code: 11022702
Display:
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GSP5,GP2,GP3,GP6,IP2,IP3,QP242,QP201,QP202,Q
P203,QP132
Cause: The Proper data item Reader1_port is set incorrectly.
Remedy: Check the Proper data item in MCS, and re-transmit it to the machine. When
change_over_mode is set to 2, 4 or 25, this must be set. This command determines where the pattern
code reader or the code reader (upper surface) connect to the communication board or the LCU connector
(the connector number is 1~8). Do not use the same port numbers for different operations (i.e. avoid 1, 3
and Command_line_port). Normally, set this to 3 for the machine and 4 for peripherals (this is normally
set when the machine is shipped).
------------------------------
Code: 11022703
Display:
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GSP5,GP2,GP3,GP6,IP3,QP242,QP201,QP202,QP20
3,QP132
Cause: The Proper data item Reader port 1 is the same as Command_line_port.
Remedy: Check the Proper data item in MCS, and re-transmit it to the machine. When
change_over_mode is set to 5 or 25, this must be set. This command determines where the pattern code
reader or the code reader (upper surface) connect to the communication board or the LCU connector (the
connector number is 1~8). Do not use the same port numbers for different operations (i.e. avoid 1, 3,
Reader1_port and Command_line_port). Normally, set this to 3 for the machine and 4
第 160 页
------------------------------
Code: 11022704
Display:
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GSP5,GP2,GP3,GP6,IP3,QP242,QP201,QP202,QP20
3,QP132
Cause: The Proper data item Reader port 2 is out of range (HELPS compatible).
Remedy: Check the Proper data item in MCS, and re-transmit it to the machine. When
change_over_mode is set to 5 or 25, this must be set. This command determines where the pattern code
reader or the code reader (upper surface) connect to the communication board or the LCU connector (the
connector number is 1~8). Do not use the same port numbers for different operations (i.e. avoid 1, 3,
Reader1_port and Command_line_port). Normally, set this to 4 for the machine and 5 for peripherals (this
is normally set when the machine is shipped).
------------------------------
Code: 11022705
Display:
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GSP5,GP2,GP3,GP6,IP3,QP242,QP201,QP202,QP20
3,QP132
Cause: The Proper data item Reader port 2 is the same as Command_line_port.
Remedy: Check the Proper data item in MCS, and re-transmit it to the machine. When
change_over_mode is set to 5 or 25, this must be set. This command determines where the pattern code
reader or the code reader (upper surface) connect to the communication board or the LCU connector (the
connector number is 1~8). Do not use the same port numbers for different operations (i.e. avoid 1, 3,
Reader1_port and Command_line_port). Normally, set this to 4 for the machine and 5 for peripherals (this
is normally set when the machine is shipped).
------------------------------
Code: 11022706
Display:
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GSP5,GP2,GP3,GP6,IP2,IP3,QP242,QP201,QP202,Q
P203,QP132
Cause: The Proper data item Code terminal port is out of range (HELPS compatible).
Remedy: Check the Proper data item in MCS, and re-transmit it to the machine. When
PCB_code_terminal is set to Use, this must be set. This command determines where the recovery code
terminal (code input) connects to the communication board or the LCU connector (the connector number
is 1~8). Do not use the same port numbers for different operations (i.e. avoid 1, 3, Reader1_port,
Reader2_port and Command_line_port). Normally, set this to 5 for the machine and 6 for peripherals (this
is normally set when the machine is shipped).
------------------------------
Code: 11022707
Display:
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GSP5,GP2,GP3,GP6,IP3,QP242,QP201,QP202,QP20
3,QP132
Cause: The Proper data items Code terminal port and Reader port 2 are the same as Command_line_port.
Remedy: Check the Proper data item in MCS, and re-transmit it to the machine. When
PCB_code_terminal is set to use, this must be set. This command determines where the recovery code
terminal (code input) connects to code terminal (code input) connects to the communication the
communication board or the LCU connector (the connector number is 1~8). Do not use the same port
numbers for different operations (i.e. avoid 1, 3, Reader1_port, Reader2_port and Command_line_port).
第 161 页
Normally, set this to 5 for the machine and 6 for peripherals (this is normally set when the machine is
shipped).
------------------------------
Code: 11022708
Display:
Used by:
Cause: Cell_status is set incorrectly.
Remedy: After checking Cell_status in MCS, re-transmit the Proper data.
"Unit cell" only exists on the ferris wheel feeder.
------------------------------
Code: 11022709
Display:
Used by: GP2,GP3,GP551,GP6,IP3,QP132
Cause: The Change_over_mode setting is incorrect.
Remedy: After checking the "change_over_mode" setting in MCS, re-transmit the Proper to the machine.
This is only effective when unit cell is in use. Do not use settings other than these. 0 = manual
terminate, 2 = pattern code reader, 4 = upper surface barcode reader, 5 = lower surface barcode reader
and 25 = barcode reader for both surfaces. For the Board Stacker, use 0 (manual terminate). For the
Ferris Wheel Feeder, use 4 (upper surface barcode reader).
------------------------------
Code: 1102270A
Display:
Used by: IP3,QP132
Cause: Command_line_status is set incorrectly.
Remedy: After checking the Command_line_status in MCS, re-transmit the Proper to the machine. LAN is
not currently recommended.
------------------------------
Code: 1102270B
Display:
Used by:
Cause: Terminal_type is set incorrectly.
Remedy: After checking the Terminal_type in MCS, re-transmit the Proper to machine. With Cell_status
at Unit, Change_over_mode at 2, 4, 5 or 25, and PCB_code_terminal at Use, this must be set. Choose
"CRX1200" or "HT." "VT-100" is not compatible.
------------------------------
Code: 1102270C
Display:
Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: The Device Check Port, Command Line Port, Reader1 Port No., Reader2 Port No., Code Terminal
Port Proper data settings are set to the same number.
Remedy: Check the Device Check Port, Command Line Port, Reader1 Port No., Reader2 Port No., Code
Terminal Port Proper data settings in MCS, re-transmit the Proper data to the machine. Check the Device
Check Port, which must be set when using the Handy Terminal. Normally this is set to 1.
1 is the first connector from the top of the first communication board. This is normally set when the
machine is shipped. Command Line Port 2 is normally set to 2. Reader1 Port No. or Reader2 Port No. are
connected with the Pattern code reader, or the lower surface code reader. These are normally set to 3 and
4. Code Terminal Port is connected when the recovery terminal (code input) is used. This is normally set
to 5. 5 is the first connector from the top of the 2nd communication board.
------------------------------
Code: 1102270D
Display:
第 162 页