FUJI错误代码查询.pdf - 第2161页

(PROGRAM/DEVICE+/GUTNSLTN) is correct. ------------------------------ Code: 2305004A Display: The Alt. Feeder is not in a loop. Set the final slot in the loop to point back to the first slot in the loop? Used by: Cause: …

Cause: When using automatic nozzle arrangement, the required number of nozzles exceed the number in

the nozzle folder.

Remedy: The program file is incorrect. Check the Nozzle Spec. file, or check the Minimum Nozzle

Diameter (PARTS/ENVDT/XP241ENVDT-/PENMI) and Maximum Nozzle Diameter

(PARTS/ENVDT/XP241ENVDT-/PENMA) settings in the part data.

------------------------------

Code: 23050043

Display: An inputted nozzle name does not exist in Nozzle Configuration File and the Nozzle Specification

File.

Used by:

Cause: The inputted nozzle name does not exist in the Nozzle Configuration file and Nozzle Specification

file.

Remedy: Try optimizing the program using [Automatic Nozzle Arrangement]. If still unsuccessful, check

the Nozzle Spec. file, or check the Minimum Nozzle Diameter (PARTS/ENVDT/XP241ENVDT-/PENMI) and

Maximum Nozzle Diameter (PARTS/ENVDT/XP241ENVDT-/PENMA) settings in the part data.

------------------------------

Code: 23050044

Display: There is no nozzle suitable for the part.

Used by:

Cause: There is no suitable nozzle available in the nozzle folder for the part.

Remedy: Open the Optimize Condition settings screen. Under the heading [Nozzle Arrangement], select

the method that was used for optimization, and correct the nozzle settings as necessary for the [Use

Present Nozzle Arrangement] or [Manual Nozzle arrangement] method. If using [Automatic Nozzle

Arrangement], check the Nozzle Spec. file, or check the Minimum Nozzle Diameter

(PARTS/ENVDT/XP241ENVDT-/PENMI) and Maximum Nozzle Diameter (PARTS/ENVDT/XP241ENVDT-

/PENMA) settings in the part data.

------------------------------

Code: 23050045

Display: There is no nozzle of the name specified for the parts.

Used by:

Cause: In the nozzle folder, there is no nozzle of the name specified for the parts.

Remedy: Open the Optimize Condition settings screen. Under the heading [Nozzle Arrangement], select

the method that was used for optimization, and correct the nozzle settings as necessary for the [Use

Present Nozzle Arrangement] or [Manual Nozzle arrangement] method. If using [Automatic Nozzle

Arrangement], check the Nozzle Spec. file, or check the Nozzle Name (PARTS/ENVDT/XP241ENVDT-

/PENNZN) in the part data.

------------------------------

Code: 23050047

Display: The Alt. Feeder number must be set to a different slot. Set the Alt. Feeder number to 0?

Used by:

Cause: A Alt. Feeder number has been set for the same slot.

Remedy: In the program file's Feeder Setup settings, and change the Alt. Feeder number

(PROGRAM/DEVICE+/GUTNSLTN) to 0 (No Alt. Feeder) or to another slot number.

------------------------------

Code: 23050048

Display: A Alt. Feeder is duplicated, or two or more first slots (reference slot) have been specified for the

same alternate feeder loop.

The Alt. Feeder settings will be deleted.

Used by:

Cause: Two or more alternate feeder loops may be overlapping.

Remedy: In the program file's Feeder Setup settings, check that the Alt. Feeder value

第 2160 页

(PROGRAM/DEVICE+/GUTNSLTN) is correct.

------------------------------

Code: 2305004A

Display: The Alt. Feeder is not in a loop. Set the final slot in the loop to point back to the first slot in the

loop?

Used by:

Cause: When arriving at a alternate feeder, a loop did not exist. The Alt. Feeder setting is zero.

Remedy: In the program file's Feeder Setup settings, check that the Alt. Feeder value

(PROGRAM/DEVICE+/GUTNSLTN) is correct.

------------------------------

Code: 2305004B

Display: The Alt. Feeder is not in a loop. Set the final slot in the loop to point back to the first slot in the

loop?

Used by:

Cause: When arriving at a alternate feeder, a non-existent Alt. Feeder setting was found.

Remedy: In the program file's Feeder Setup settings, check that the Alt. Feeder value

(PROGRAM/DEVICE+/GUTNSLTN) is correct.

------------------------------

Code: 2305004C

Display: Nozzle name is not specified. Assume as a standard nozzle?

Used by:

Cause: In the Nozzle folder information file, the Nozzle name is not specified for "GNANAM".

Remedy: When [Yes] is selected, standard Nozzle name is specified according to the diameter. When [No]

is selected, no Nozzle is specified to the Nozzle folder.

------------------------------

Code: 230500A1

Display: The source program is already in an optimized condition. It is not possible to further optimize the

source program.

Used by:

Cause: The post-optimized theoretical cycle time is slower than the pre-optimized time, however, source

program sequence or feeder setup problems have been fixed.

Remedy: It may be possible to achieve a better cycle time result by changing the optimization conditions,

if production constraints allow.

------------------------------

Code: 23060003

Display: The tape width is outside the specifications or is zero.

Used by:

Cause: The packaging name (PARTS/HEADER/CMPNAME) or the tape width (PARTS/PACKLS-

/TAPEWIDTH) is outside the specifications or is zero. For packaging name, one of the following types must

be specified: E08xx, E12xx, E16xx, E24xx, E32xx, J32xx, E44xx, E56xx, E72xx, E88xx. For tape width,

one of the following must be specified: 8, 12, 16, 24, 32, 44, 56, 72, 88.

Remedy: The tape width setting in the part data is incorrect. Check the file contents.

------------------------------

Code: 23060005

Display: A feeder does not exist in the slot referred to in the sequence.

Used by:

Cause: A feeder does not exist in the slot referred to in the sequence.

Remedy: The program file is incorrect. Check and correct the file contents.

------------------------------

Code: 23060006

Display: Part data referred to by the sequence slot does not exist.

第 2161 页

Used by:

Cause: The Part data, referred to by a sequence slot that contains no skipped board/feeder/sequence

setting, does not exist.

Remedy: The program file is incorrect. Check and correct the file contents.

------------------------------

Code: 23060008

Display: No feeder exists in the slot referenced by this skipped sequence (for skipped sequences included

in optimization).

Used by:

Cause: A feeder does not exist in a sequence slot that contains board/feeder/sequence skip settings.

Remedy: The program file is incorrect. Check and correct the file contents.

------------------------------

Code: 2306000A

Display: No part data exists for the slot referenced by this skipped sequence (for skipped sequences

included in optimization).

Used by:

Cause: The part data referred to by a sequence slot containing board/feeder/sequence skip settings does

not exist.

Remedy: The program file is incorrect. Check and correct the file contents.

------------------------------

Code: 2306000D

Display: The Alt. Feeder does not exist. Do you want to set 0 for alternate feeder?

Used by:

Cause: A feeder is not set in the Alt. Feeder specified for the displayed stage-slot.

Remedy: The Feeder Setup information in the program file is incorrect. Check the settings.

------------------------------

Code: 2306000E

Display: There are too many feeders allocated to one stage.

Used by:

Cause: When automatic feeder arrangement was selected at the Optimize Condition settings screen, the

number of feeders allocated to the stage exceeded the maximum feeder slots.

Remedy: Firstly, try changing the [Use Feeder Type] settings. If unsuccessful, perform optimization using

the [Alt. Feeders Are Removed] setting. If still unsuccessful, reduce the part varieties used in the program.

------------------------------

Code: 23060010

Display: A currently unused feeder has been fixed, however, no part data exists for that slot.

Used by:

Cause: There is no part data displayed in the Feeder Setup.

Remedy: The program file data is incorrect. Check the contents.

------------------------------

Code: 23060012

Display: When using [Fix Feeders], there is no such slot available for the feeder.

Used by:

Cause: The specified stage - slot number does not exist.

Remedy: Check the program file's stage number (PROGRAM/DEVICE+/GUTSTN) and slot number

(PROGRAM/DEVICE+/GUTSLTN), or alternatively use the [Automatic Most Suitable Feeder Arrangement]

setting for optimization.

------------------------------

Code: 23060013

Display: When using [Fix Feeders], a feeder is too wide to place at an end slot was specified.

Used by:

第 2162 页