FUJI错误代码查询.pdf - 第822页

select station upper and lower limit sensors are functioning normally. ------------------------------ Code: 1207E?2B Display: "SCU?(ICM,PMC?) Error Code:********" (QP2) "TY Not in Safe Vertcl Pos." (Q…

Code: 1207E?25

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Tray Rejection Error" (QP2,QP2,NP3)

Used by: QP242,QP201,QP202,QP203,QP2,NP3

Cause: Tray ejection error (tray passage confirmation error).

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Check whether the ejected tray has gotten caught on something. Make sure the tray ejection

check sensor is functioning normally.

------------------------------

Code: 1207E?26

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Board Setting Error" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: Board setting error.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Set the hole in the board on the reference pin. Make sure that the board setting check sensor is

functioning normally.

------------------------------

Code: 1207E?27

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Board Clamp/Unclamp Timeout" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: Board transport error (board clamp/unclamp timeout).

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Check whether something is interfering with the board elevator. Make sure the board elevator

upper and lower limit sensors are functioning normally.

------------------------------

Code: 1207E?28

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Board Stpper Up/dwn Timeout" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: Board transport error (board stopper up/down timeout).

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Check whether something is interfering with the board stopper. Make sure the board stopper

upper and lower limit sensors are functioning normally.

------------------------------

Code: 1207E?29

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Nzl Cyl Fwd/Rtrct Timeout" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: Nozzle index cylinder forward/retract timeout.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: This error should not occur under normal conditions.

------------------------------

Code: 1207E?2A

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Nzl Chngr Up/Dwn Timeout" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: Nozzle select station up/down timeout.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Check whether something is interfering with the nozzle select station. Make sure the nozzle

第 821 页

select station upper and lower limit sensors are functioning normally.

------------------------------

Code: 1207E?2B

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"TY Not in Safe Vertcl Pos." (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: The TZ-axis cannot be moved because the TY-axis is not in a position that allows vertical

movement.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Use inching or another method to return the TY-axis to a position (i.e., the forward or retract

end) that will allow the TZ-axis to be moved.

------------------------------

Code: 1207E?2C

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"TY Not at Forward End" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: The TZ-axis cannot be moved because the TY-axis is not at the forward end.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Use inching or another method to move the TY axis to the forward end.

------------------------------

Code: 1207E?2D

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"TZ Incorrect Stop Pos." (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: The TY-axis cannot be moved because the TZ-axis is not stopped at the correct position.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Use inching or another method to return the TZ-axis to a position that will allow the TY-axis to

be moved.

------------------------------

Code: 1207E?2E

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Mag.slot Occupied w/ Tray" (QP2)

Used by: QP242

Cause: A tray cannot be stored in the magazine tray slot because the slot is already occupied by a tray.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Remove the tray from the magazine, and store it at another device position in the magazine.

------------------------------

Code: 1207E?2F

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"RS Port Not Set / MTU6" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: The MTU6 cannot be started because the RS port has not been set.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: This error should not occur under normal conditions.

------------------------------

Code: 1207E?30

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"RS Cable Not Conected/MTU6" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: The MTU6 cannot be started because the RS cable is not connected.

(value replacing "?" is module number; error code appears in place of asterisks)

第 822 页

Remedy: Check whether the RS cable to the MTU6 is disconnected.

------------------------------

Code: 1207E?31

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"RS Port Not Set / Flux" (QP2)

Used by: QP242

Cause: The flux application pump cannot be started because the RS port has not been set.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: This error should not occur under normal conditions.

------------------------------

Code: 1207E?32

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"RS Cable Not Connected/Flux" (QP2)

Used by: QP242

Cause: The flux application pump cannot be started because the RS cable is not connected.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: This error should not occur under normal conditions.

------------------------------

Code: 1207E?33

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Inexcutable (FZ not up-end)" (QP2)

Used by: QP242

Cause: The command cannot be executed because the flux application axis (FZ-axis) is not at the upper

limit.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Use an I/O command or other method to raise the flux head.

------------------------------

Code: 1207E?34

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Pstn'g time-out (FX/TY/TZ)" (QP2)

Used by: QP242,QP201,QP202,QP203

Cause: Positioning timeout (FX-axis, TY-axis, or TZ-axis).

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Check whether something is interfering with the above-named axes, or whether the axis action

has become extremely heavy. Check the robust controller for problems.

------------------------------

Code: 1207E?35

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"FZ-axis operation time-out" (QP2)

Used by: QP242

Cause: Timeout during FZ-axis operation.

(value replacing "?" is module number; error code appears in place of asterisks)

Remedy: Check whether something is interfering with the FZ-axis. Make sure that the upper and lower

limit sensors are functioning normally.

------------------------------

Code: 1207E?36

Display: "SCU?(ICM,PMC?) Error Code:********" (QP2)

"Syringe size parameter 0" (QP2)

Used by: QP242

Cause: The parameter that specifies the flux syringe size is set to 0.

(value replacing "?" is module number; error code appears in place of asterisks)

第 823 页