FUJI错误代码查询.pdf - 第1893页
Display: Machine Type Table read error Used by: Cause: The Machine Type table could not be read. Remedy: Re-install the software. ------------------------------ Code: 2100602F Display: set device data after FIX Used by: …
Remedy: Check the file (fix and save).
------------------------------
Code: 21006026
Display: source file program information read error
Used by:
Cause: Unable to read the source program.
Remedy: Check the file (fix and save).
------------------------------
Code: 21006027
Display: source file device data read error
Used by:
Cause: The device data in the source program could not be read.
Remedy: Check the source program.
------------------------------
Code: 21006028
Display: source file sequence data read error
Used by:
Cause: The sequence data in the source program could not be read.
Remedy: Check the source program.
------------------------------
Code: 21006029
Display: Permanent Set Table file open error
Used by:
Cause: The Permanent Set Table could not be opened.
Remedy: Check the Permanent Set Table file.
------------------------------
Code: 2100602A
Display: Permanent Set Table file offset table read error
Used by:
Cause: The Permanent Set Table file could not be read.
Remedy: Check the file.
------------------------------
Code: 2100602B
Display: Permanent Set Table file offset table read error
Used by:
Cause: The Permanent Set Table file could not be read.
Remedy: Check the file.
------------------------------
Code: 2100602C
Display: separate frame read error
Used by:
Cause: The separate frame could not be read.
Remedy: Re-execute the function. If it still doesn't work, reboot MCS.
------------------------------
Code: 2100602D
Display: device data already set
Used by:
Cause: The same device was already specified.
Remedy: Fix by checking the device comments.
------------------------------
Code: 2100602E
第 1892 页
Display: Machine Type Table read error
Used by:
Cause: The Machine Type table could not be read.
Remedy: Re-install the software.
------------------------------
Code: 2100602F
Display: set device data after FIX
Used by:
Cause: Unplaced devices were run through the separator after the fixed devices. There is no fixed device
sequence for the specified set device in the permanent set table.
Remedy: This is a warning. It is not an error message.
------------------------------
Code: 21006030
Display: separate frame open error
Used by:
Cause: The separate frame could not be opened.
Remedy: Re-execute the function. If it still doesn't work, re-boot MCS.
------------------------------
Code: 21006031
Display: can't get queue pointer "getqp"
Used by:
Cause: A system error has occurred.
Remedy: Re-boot MCS.
------------------------------
Code: 21006032
Display: can't dequeue "deque"
Used by:
Cause: A system error has occurred.
Remedy: Re-boot MCS.
------------------------------
Code: 21006033
Display: can't queue "queing"
Used by:
Cause: A system error has occurred.
Remedy: Re-boot MCS.
------------------------------
Code: 21006034
Display: HFIX file open error
Used by:
Cause: The temporary file defining the half-fixed (HFIX) parts could not be opened.
Remedy: Re-execute the function. If it still doesn't work, re-boot MCS.
------------------------------
Code: 21006035
Display: HFIX file read error
Used by:
Cause: The temporary file defining the half-fixed (HFIX) parts could not be read.
Remedy: Re-execute the function. If it still doesn't work, re-boot MCS.
------------------------------
Code: 21006036
Display: can't create HFIX file
Used by:
第 1893 页
Cause: The temporary file defining the half-fixed (HFIX) parts could not be created.
Remedy: Re-execute the function. If it still doesn't work, re-boot MCS.
------------------------------
Code: 21006037
Display: HFIX file write error
Used by:
Cause: Data could not be written to the temporary file defining the half-fixed (HFIX) parts.
Remedy: Contact Fuji.
------------------------------
Code: 21006038
Display: separate frame write error
Used by:
Cause: Data could not be written to the separate frame.
Remedy: Re-execute the function. If it still doesn't work, re-boot MCS.
------------------------------
Code: 21006039
Display: Part Data file not found
Used by:
Cause: The required Part Data does not exist.
Remedy: Make sure that the Part Data referred to by the source program has been stored.
------------------------------
Code: 2100603A
Display: Part Data offset table read error
Used by:
Cause: The Part Data could not be read.
Remedy: Create an offset table file.
------------------------------
Code: 2100603B
Display: Part Data read error
Used by:
Cause: Unable to read Part data.
Remedy: Create a Part data file.
------------------------------
Code: 2100603C
Display: can't create UN_SEP reason file
Used by:
Cause: The UN_SEP file could not be created.
Remedy: If there are other UN_SEP files, delete them. If there is very little memory remaining on the hard
disk, eliminate unnecessary files or perform maintenance on the hard disk.
------------------------------
Code: 2100603D
Display: UN_SEreason file write error
Used by:
Cause: The UN_SEP reason file could not be written to.
Remedy: If there is very little memory remaining on the hard disk, eliminate unnecessary files or perform
maintenance on the hard disk.
------------------------------
Code: 2100603E
Display: can't create separate frame
Used by:
Cause: The separate frame could not be created.
第 1894 页