FUJI错误代码查询.pdf - 第4821页

Remedy: Check the condition of the part presence check sensor. Refer to the last four digits of the unit error code for details. ------------------------------ Code: 95920000 Display: An error occurred measuring a defaul…

100%1 / 5282
( 补充编码 上４位数 支撑销X坐标[mm]
下４位数 支撑销Y坐标[mm]
坐标为生产Job∶BackupPin坐标。小数点以下省略了。 )
Remedy: ·请打开对象Job的Job builder，确认对象机器的BackupPin坐标的设定。和电路板停止块有干涉时请进
行坐标的编辑和再传送。编辑后电路板停止块附近需要支撑销时，请手动配置支撑销。
------------------------------
Code: 95750000
Display: BOARD.PANEL数据值异常∶电路板的X方向长度
Used by: NXT,AIM
Cause: 在单搬运轨道S上，生产Job的BOARD.PANEL数据部分的电路板X方向长度的值(电路板搬入角度为
90°270°时为Y)超过了上限值。
公差范围∶50.00~520.00
( 补充编码 )
Remedy: 请打开对象Job的Job builder，确认General标签页的Panel Information处的电路板的设定。如果设定有
问题时，请手动进行修正后再传送。
------------------------------
Code: 95760000
Display: BOARD,PANEL数据值异常∶电路板的Y方向长度
Used by: NXT,AIM
Cause: 在单搬运轨道S上，生产Job的BOARD.PANEL数据部分的电路板Y方向长度的值(电路板搬入角度为
90°270°时为X)超过了上限值。
公差范围：
电路板挡块－(Standard)：50.00~457.00
电路板挡块－(Wide)：100.00~457.00
( 补充编码 )
Remedy: 请打开对象Job的Job builder，确认General标签页的Panel Information处的电路板的设定。如果设定有
问题时，请手动进行修正后再传送。
------------------------------
Code: 95770000
Display: 挡块种类不匹配
Used by: NXT,AIM
Cause: JOB中所设定的电路板挡块类别与安装在机器上的挡块类别不匹配。
( 补充编码 )
Remedy: 缺口电路板有可能不能在正确的位置上停止。请安装JOB中所设定的类别的电路板挡块。电路板挡块的类别
能够在MachineConfiguration－Process Options标签页的Panel Stopper Type中得到确认。
------------------------------
Code: 95900000
Display: An internal processing error occurred
Used by: NXT,AIM
Cause: The process was discontinued due to an illegal process within the system.
( Additional )
Remedy: If this does not resolve the problem, acquire trace data from the machine under the conditions in
which the error occurs, and contact your Fuji representative.Turn off the main switch and restart the
machine.
------------------------------
Code: 95910000
Display: Part presence check: Sensor error
Used by: NXT,AIM
Cause: When the machine was started, the status of the part presence check sensor was checked. A part
was detected although no part has been picked up.
( Additional )
第 4820 页
Remedy: Check the condition of the part presence check sensor.
Refer to the last four digits of the unit error code for details.
------------------------------
Code: 95920000
Display: An error occurred measuring a default value
Used by: NXT,AIM
Cause: An error occurred measuring a default value.
( Additional )
Remedy: Refer to the last four digits of the unit error code for details.
------------------------------
Code: 95930000
Display: Part presence check: Sensor error
Used by: NXT,AIM
Cause: After nozzle changeover (placement), the condition of the part presence check sensor was
checked. A part was found although no part has been picked up.
( Additional )
Remedy: Check the condition of the part presence check sensor.
Refer to the last four digits of the unit error code for details.
------------------------------
Code: 95A00000
Display: An internal processing error occurred
Used by: NXT,AIM
Cause: The process was discontinued due to an illegal process within the system.
( Additional )
Remedy: If this does not resolve the problem, acquire trace data from the machine under the conditions in
which the error occurs, and contact your Fuji representative.Turn off the main switch and restart the
machine.
------------------------------
Code: 95A10000
Display: 意想不到的异常
Used by: NXT,AIM
Cause: 种类的取得、标记的确认、固有值的取得及设定等的异常。
（补充编码）
Remedy: 对不起麻烦您获取发生错误时的跟踪数据，与敝公司Support联系。
------------------------------
Code: 95A20000
Display: XY机械手异常
Used by: NXT,AIM
Cause: 想要使XY机械手动作时，发生了异常。
·伺服异常
·Xs位置异常
（补充编码）
Remedy: 由于在想要使XY机械手动作时发生了异常，因此请参照单元错误编码。
------------------------------
Code: 95A30000
Display: 影像处理装置异常
Used by: NXT,AIM
Cause: 发生了影像处理装置异常。
·影像处理装置的版本不一致
·影像处理装置的拍摄准备指示异常
·影像处理装置的拍摄指示异常
第 4821 页
·影像处理装置的等待曝光结束异常
·影像处理装置的影像处理指示异常
·影像处理装置的影像处理结果取得异常
（补充编码）
Remedy: (1)请确认触发电路。
(2)请确认版本。
(3)请更换影像处理电路板。
详细请参照单元错误编码来解决。
------------------------------
Code: 95A40000
Display: 工作头异常
Used by: NXT,AIM
Cause: 想要使工作头动作时发生了异常。
可考虑以下的原因。
·伺服异常
·Z轴移动范围异常
·初始动作Z轴高度异常
·吸嘴落下异常，吸嘴不正确安装异常
（补充编码）
Remedy: 由于想要使工作头动作时发生了异常，因此请参照单元错误编码来解决。
------------------------------
Code: 95A50000
Display: 影像处理失败
Used by: NXT,AIM
Cause: 影像处理结果为异常。
( 补充编码 影像处理装置的错误编码 )
Remedy: ·请确认相机上的玻璃是否脏。
·请确认相机的灯是否亮灯。
·请确认拍摄区域上是否有异物落下。
·请确认治具吸嘴的前端是否脏。
详细请通过单元错误编码来确认。
------------------------------
Code: 95A60000
Display: 贴装角度测定结果超出公差值
Used by: NXT,AIM
Cause: 贴装角度测定后的结果超出了公差值。
( 补充编码 显示测定结果。
单位：[1/1000deg] )
Remedy: ·在拍摄处理治具吸嘴前端的定位点时，请确认是否识别了错误的定位点或异物。
·请确认相机的光源是否充分亮。
·请确认吸嘴前端是否弯曲。
------------------------------
Code: 95A70000
Display: 治具吸嘴未安装
Used by: NXT,AIM
Cause: 本测定需要治具吸嘴，但是由于谋种原因，治具吸嘴没有被安装。
（补充编码）
Remedy: ·请确认工作头上是否安装了吸嘴。
·请确认是否吸嘴落下。
·请确认工作头的吸嘴识别I/O是否正确地反应。
------------------------------
第 4822 页