FUJI错误代码查询.pdf - 第861页

------------------------------ Code: 121???21 Display: Coplanarity error(NP2,QP3) Used by: QP242,NP2,QP3 Cause: A command sequence error occurred. The command could not be executed at the LLL board. Remedy: Restart the s…

Cause: There are no leads on the part where a lead coplanarity check is occurring.

Remedy: Do not perform a lead coplanarity check for parts without leads. Verify that the part data

(number of leads) is set correctly.

------------------------------

Code: 121???0C

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Either an error or a time up condition occurred when the LLL board linearity calculation

command was executed.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???0D

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Either an internal processing error or a time up condition occurred when the LLL board linearity

calculation command was executed.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???0E

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An error occurred when the linearity calculation result was received or checked. Either a

communication time up condition occurred, or no leads were detected, resulting in no calculation result.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off. Also verify that the part size is correct.

------------------------------

Code: 121???0F

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An attempt to obtain linearity calculation results from the LLL board ended in failure. Either a

communication time up occurred, or the lead bend amount exceed the permissible range.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???10

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An error occurred when the coplanarity calculation result was received or checked. A

communication time up occurred.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

------------------------------

Code: 121???11

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: An attempt to obtain coplanarity calculation results from the LLL board ended in failure. Either a

communication time up occurred, or the lead bend amount exceed the permissible range.

Remedy: If the LLL baud rate is less than 9600bps, set it to 9600bps or higher. (Time up) If the problem

continues, turn the power off.

第 860 页

------------------------------

Code: 121???21

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: A command sequence error occurred. The command could not be executed at the LLL board.

Remedy: Restart the system, and repeat the operation from the beginning.

------------------------------

Code: 121???22

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Insufficient data error. LLL board calculation ended in failure due to insufficient data. Lead

measurement was not performed, and no pulse was received from the encoder. A coplanarity calculation

was attempted after scanning 1 side.

Remedy: Set the Lead-Length (in part data) as accurately as possible. Increase the Scan Offset to permit

measurement of the full length of the lead. Lead coplanarity checks are possible for SOIC or QFP parts.

------------------------------

Code: 121???23

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Parameter error. The received data is invalid for the LLL..

Remedy: Check the Coplanarity item in part data.

------------------------------

Code: 121???24

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Invalid command. The attempted command is invalid for the LLL..

Remedy: Execute a reset start.

------------------------------

Code: 121???30

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Serial communication "receive overrun" error.

Remedy: Restart the system and repeat the operation from the beginning.

------------------------------

Code: 121???31

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Serial communication "parity" error.

Remedy: Restart the system and repeat the operation from the beginning.

------------------------------

Code: 121???32

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Serial communication "framing" error.

Remedy: Restart the system and repeat the operation from the beginning.

------------------------------

Code: 121???40

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Communication with "Sensor 0 EEPROM Readback Error sensor 0" is not occurring. Sensor

cable is severed or disconnected.

第 861 页

Remedy: Check the sensor cable continuity, and replace the cable if necessary.

------------------------------

Code: 121???42

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Communication with "Sensor Synchronization Error sensor 0" is not occurring. Sensor cable is

severed or disconnected.

Remedy: Check the sensor cable continuity, and replace the cable if necessary.

------------------------------

Code: 121???50

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: "Expecting FIFO Empty VME" board failure.

Remedy: Turn the power off and execute a reset start.

------------------------------

Code: 121???60

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Laser beam was uninterrupted at the wrong point, or was never interrupted.

Remedy: Check the sensor mount position and the lead measurement position. If this occurs during lead

measurement, verify that the part data "Lead Length" is set as accurately as possible. Increase the

"lead_offset" for the "Coplanarity" item in part data to ensure that the full length of the lead is measured.

------------------------------

Code: 121???61

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Laser beam was interrupted at the wrong point, or is still interrupted.

Remedy: Verify that no foreign matter or parts are adhering to the sensor. Verify that the body is not

being measured instead of the lead during lead measurements.

------------------------------

Code: 121???70

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Coplanarity calculation results indicate a lead height above the "Coplanarity Tolerance" height

(part data).

Remedy: Check for raised part leads. Verify that the "Coplanarity Tolerance" value (part data) is not too

small.

The coplanarity check result can be viewed at the [Coplanarity] screen. (QP3)

However, only the most recently performed check for each holder can be viewed. (QP3)

The [Coplanarity] screen can be reached through the following path: [Main] -[Maintenance] -

[Coplanarity]. (QP3)

------------------------------

Code: 121???71

Display: Coplanarity error(NP2,QP3)

Used by: QP242,NP2,QP3

Cause: Linearity calculation results indicate a lead which is outside the "Linear Tolerance" plane (part

data).

Remedy: Check for bent part leads. Verify that the "Linear Tolerance" value (part data) is not too small.

The coplanarity check result can be viewed at the [Coplanarity] screen. (QP3)

However, only the most recently performed check for each holder can be viewed. (QP3)

The [Coplanarity] screen can be reached through the following path: [Main] -[Maintenance] -

第 862 页