FUJI错误代码查询.pdf - 第456页

Code: 12037003 Display: Memory allocation error Used by: Cause: An error occurred due to a lack of memory in the machine control software. This error occurred when Fuji OS system call_test (_GET_GLOBAL) which secures mem…

100%1 / 5282
Cause: The laser beam was unblocked at the wrong point or was not completely blocked.
Remedy: Check the positions of the sensor and the lead location. If this error occurs while the lead is
being measured, check that the lead lengths set in Part data (Vision data items 10.Lead_length_x,
11.Lead_length_y) are as accurate as possible. Make the offset in Coplanarity item 4.Y_offset larger and
measure the lead.
------------------------------
Code: 12036041
Display: Expecting Beam Unblocked
Used by: IP1,IP2,IP3
Cause: The laser beam was blocked at the wrong point or was not completely unblocked.
Remedy: Check that there are no foreign particles blocking the sensor. Check that the part being
measured has leads.
------------------------------
Code: 12036042
Display: LLL:Sensor DAC Error
Used by: IP1,IP2,IP3,QP242
Cause: The LLL sensor is damaged.
Remedy: Contact Fuji.
------------------------------
Code: 12036050
Display: LLL: NPX Error
Used by: IP1,IP2,IP3,QP242
Cause: The LLL controller is damaged.
Remedy: Contact Fuji.
------------------------------
Code: 12037000
Display: Memory allocation error
Used by: CP5,GP551,GP6,QP242,QP201,QP202,QP203
Cause: An error occurred due to a lack of memory in the machine control software. This error occurred
when Fuji OS system call_test (_MALLOC) which secures a new memory block was used.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037001
Display: Memory allocation error
Used by: CP3,CP4-1,CP4-2,CP4-3
Cause: An error occurred due to a lack of memory in the machine control software. This error occurred
when Fuji OS system call_test (_GET_HEEP) which secures memory of a specified size in the global field
was used.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037002
Display: Memory allocation error
Used by:
Cause: An error occurred due to a lack of memory in the machine control software. This error occurred
when Fuji OS system call_test (_GET_MEMORY) which secures memory of a specified size in the stack
field was used.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
第 455 页
Code: 12037003
Display: Memory allocation error
Used by:
Cause: An error occurred due to a lack of memory in the machine control software. This error occurred
when Fuji OS system call_test (_GET_GLOBAL) which secures memory of a specified size in the standard
memory was used.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037004
Display: RB UDT creation error
Used by:
Cause: In conjunction with the internal processing of the machine software, an attempt was made to
create a robust unit data table using the _create_robust_udt() system call of the Fuji operation system.
However, table creation was not successful because of insufficient memory.
Remedy: Reboot the machine using the reset-start procedure. If operation works properly after the reset-
start then wait in this status for several minutes. Consult Fuji if nothing changes even after a reset-start
is carried out or if the same type of symptoms occur frequently.
------------------------------
Code: 1203701?
Display: RB SRV creation error
Used by: GP551,GP6
Cause: In conjunction with the internal processing of the machine software, an attempt was made to
create a robust servo driver using the _create_robust_srv() system call of the Fuji operation system.
However, servo driver creation was not successful because of insufficient memory. The last digit in the
error code indicates the number of the axis for which creation was attempted.
Remedy: Reboot the machine using the reset-start procedure. If operation works properly after the reset-
start then wait in this status for several minutes. Consult Fuji if nothing changes even after a reset-start
is carried out or if the same type of symptoms occur frequently.
------------------------------
Code: 1203710?
Display: MX100 creation error
Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GP551,GP6
Cause: An error occurred during initialization of a board or in communication with a board. This error
occurred when Fuji OS system call_create_k300() which manages board initialization was used to generate
event control blocks (ICB) for the remote I/O and the OP link. The last number in the error code indicates
the number of the board in which the error occurred. 0 indicates the first board.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 1203711?
Display: MX100 creation error
Used by: CP4-1,CP4-2,CP4-3,CP5,CP642,CP643,GL541,GP551,GP6
Cause: An error occurred in the machine control software . This error occurred when Fuji OS system
call_create_k300() which generates event control blocks (ICB) for the remote I/O and the OP link was used.
The last number in the error code indicates the number of the board in which the error occurred. 0
indicates the first board.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 1203712?
第 456 页
Display: I/O creation error
Used by: CP3,GP551,GP6,QP242,QP201,QP202,QP203
Cause: An error occurred due to a lack of memory in the machine control software. This error occurred
when Fuji OS system call_create_pia() which generates event control blocks (ICB ) for VM-1520, VM-1540,
and ACTIVE_PIA was used. The last number in the error code indicates the number of the board in which
the error occurred. 0 indicates the first board.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037130
Display: I/O creation error
Used by:
Cause: An error occurred due to a lack of memory in the machine control software. This error occurred
when Fuji OS system call_create_in() which generates event control blocks (ICB) for sequential address
input such as LUC and TSA-150 was used.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037140
Display: I/O creation error
Used by:
Cause: An error occurred due to a lack of memory in the machine control software. This error occurred
when Fuji OS system call_system(_CREATE_ICB) which generates input control blocks (ICB) for digital
input was used.
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037150
Display: Interrupt creation error
Used by:
Cause: An attempt was made to register an interrupt as an entry interrupt but the vector number was
over 181. The entry interrupt registration was made by Fuji OS system call_create_int().
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037160
Display: Interrupt creation error
Used by: CP4-1,CP4-2
Cause: An attempt was made to register in the CPU a certain interrupt as an event issuing interrupt but
the vector number was over 181. Registration of the event issuing interrupt was made by Fuji OS system
call_create_int().
Remedy: Press RESET and then resume operation. If this error occurs frequently or cannot be corrected,
notify Fuji.
------------------------------
Code: 12037200
Display: CPU CH1 creation error
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,GP551,GP6,QP242,QP201,QP202,QP203
Cause: An error occurred due to a lack of memory in the machine control software. This error occurred
when Fuji OS system call_create_cpu_com() which automatically generates communication drivers for a 16
or 32 bit CPU board's channel 1 serial port was used.
第 457 页