FUJI错误代码查询.pdf - 第1849页
Remedy: Check whether the new version of the log has been installed. If the previous version is in the machine, erase and reset. If the new version has already been installed, re-boot the system. ------------------------…
Remedy: 停止自动运转，再次从Fuji Flexa传输Job。
------------------------------
Code: 1F020208
Display: 电文错误
Used by: FKSP1
Cause: 接收到来自Fuji Flexa的Machine Communicate service的非法电文指令。
Remedy: 可能是生产线设定有误。
请在Fuji Flexa确认生产线设定。修正为正确的设定后，执行生产线变更通知。
------------------------------
Code: 1F020209
Display: 执行错误
Used by: FKSP1
Cause: 所指定的通道号码超出了机器的最大搬运轨道数量。
Remedy: 可能是生产线设定有误。
请在Fuji Flexa确认生产线设定。确认机器的搬运轨道数量与生产线设定的搬运轨道数量是否一致。
------------------------------
Code: 1F02020A
Display: 执行错误
Used by: FKSP1
Cause: 取得模型名失败。
Remedy: Fuji Flexa有可能未进行生产线变更通知。请再次执行生产线变更通知。
------------------------------
Code: 1F02020B
Display: 执行错误
Used by: FKSP1
Cause: 取得机器别名失败。
Remedy: Fuji Flexa有可能未进行生产线变更通知。请再次执行生产线变更通知。
------------------------------
Code: 1F02020C
Display: 执行错误
Used by: FKSP1
Cause: Fuji Flexa用户服务器的设定不正确。
Remedy: 请确认执行了生产线变更通知的Fuji Flexa和机器上的Fuji Flexa的用户服务器的设定。
------------------------------
Code: 1F02020D
Display: 执行错误
Used by: FKSP1
Cause: 取得机器配置信息失败。
Remedy: 所安装的文件有可能未被正确安装、或者文件已损坏。
请再次安装FKSP1 Communication service。
------------------------------
Code: 1F020301
Display: 通信错误
Used by: FKSP1
Cause: 发生通信指令的送信错误。
Remedy: 请确认机器应用程序是否正常运行。未运行时，请重新启动机器应用程序。
------------------------------
Code: 21000000
Display: Log File Logging error (****)
Used by:
Cause: Log file cannot carry out logging.
第 1848 页
Remedy: Check whether the new version of the log has been installed. If the previous version is in the
machine, erase and reset. If the new version has already been installed, re-boot the system.
------------------------------
Code: 21000001
Display: Transmition error (****)
Used by:
Cause: There was an error in transmission.
Remedy: Check that the machine power is on, and that the cables are correctly connected. Check that
the machine and MCS are using the same version.
------------------------------
Code: 21000002
Display: Analyzer pipe open error (****)
Used by:
Cause: The analyzer pipe could not be opened.
Remedy: Check whether there is a pipe or not. If not, re-boot MCS.
------------------------------
Code: 21000003
Display: Console pipe open error (****)
Used by:
Cause: The console pipe could not be opened.
Remedy: Check whether or not there is a pipe. If not, re-boot MCS.
------------------------------
Code: 21000004
Display: Event iink error (****)
Used by:
Cause: The event could not be linked.
Remedy: Re-boot MCS.
------------------------------
Code: 21000005
Display: Console display error (****)
Used by:
Cause: No information is displayed on the monitor.
Remedy: Check that the monitor is plugged in, and is properly connected to the computer.
------------------------------
Code: 21000006
Display: Log file create error (****)
Used by:
Cause: Unable to create the logfile.
Remedy: Check the conditions of the hard disk (available memory, file partitions, etc.).
------------------------------
Code: 21000007
Display: pipe read error (****)
Used by:
Cause: The pipe could not be read.
Remedy: Re-boot MCS.
------------------------------
Code: 21000008
Display: Line Descriputer read error (****)
Used by:
Cause: The line descriptor could not be read.
Remedy: Check the line descriptor file.
第 1849 页
------------------------------
Code: 21000009
Display: Transmition pipe open error (****)
Used by:
Cause: The transmission pipe could not be opened.
Remedy: If there is no pipe, re-boot MCS.
------------------------------
Code: 2100000A
Display: Mother pipe open error (****)
Used by:
Cause: The mother pipe could not be opened.
Remedy: Check the pipe. If there is no pipe, reboot MCS.
------------------------------
Code: 2100000B
Display: Transmition error (dA) (****)
Used by:
Cause: dA transmission could not be carried out.
Remedy: Check that the machine power is on and that the cables are connected properly.
------------------------------
Code: 2100000C
Display: Terminal pipe open error (****)
Used by:
Cause: The terminal pipe could not be opened.
Remedy: Check the terminal pipe. If it is not there, re-boot MCS.
------------------------------
Code: 2100000D
Display: can't Find line or MC nick name (****)
Used by:
Cause: The specified line name or machine nickname is incorrect.
Remedy: Check the line descriptor and nickname and repeat the input.
------------------------------
Code: 2100000E
Display: Log File read error (****)
Used by:
Cause: The log file could not be read.
Remedy: Check the log file.
------------------------------
Code: 2100000F
Display: Log File directory create error (****)
Used by:
Cause: The log file directory could not be created.
Remedy: Check the machine nickname entered in the line descriptor.
------------------------------
Code: 21000010
Display: loglist pipe open error (****)
Used by:
Cause: The loglist pipe could not be opened.
Remedy: Check that there is a pipe. If there is no pipe, re-boot MCS.
------------------------------
Code: 21000011
Display: Line_monitor pipe open error (****)
第 1850 页