FUJI错误代码查询.pdf - 第2096页
Remedy: Correct the file name. ------------------------------ Code: 2100EDB0 Display: Used by: Cause: The MCS/2 Part Data directory could not be opened. Remedy: Check the directory. ------------------------------ Code: 2…
Display:
Used by:
Cause: The temporary file for translation could not be created.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDA8
Display:
Used by:
Cause: The temporary file for translation could not be opened.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDA9
Display:
Used by:
Cause: Data could not be written to the temporary file for translation.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDAA
Display:
Used by:
Cause: The temporary file for translation could not be read.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDAB
Display:
Used by:
Cause: The file to be translated does not exist in MCS/1.
Remedy: Correct the specified object file name.
------------------------------
Code: 2100EDAC
Display:
Used by:
Cause: The Part Data Translator could not be started up.
Remedy: Reinstall the translator software.
------------------------------
Code: 2100EDAD
Display:
Used by:
Cause: The floppy disk drive could not operate.
Remedy: Make sure that the floppy disk drive lock lever is fully closed.
------------------------------
Code: 2100EDAE
Display:
Used by:
Cause: The name of the file has not been specified.
Remedy: Specify the name of the file.
------------------------------
Code: 2100EDAF
Display:
Used by:
Cause: Filename syntax error.
第 2095 页
Remedy: Correct the file name.
------------------------------
Code: 2100EDB0
Display:
Used by:
Cause: The MCS/2 Part Data directory could not be opened.
Remedy: Check the directory.
------------------------------
Code: 2100EDB1
Display:
Used by:
Cause: The temporary file to display Part data could not be created.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDB2
Display:
Used by:
Cause: The temporary file to display Part data could not be created.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDB3
Display:
Used by:
Cause: Data could not be written to the temporary file to display Part data.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDB4
Display:
Used by:
Cause: A module does not exist.
Remedy: Re-install the translator software.
------------------------------
Code: 2100EDB5
Display:
Used by:
Cause: The system command (Dir) could not be used.
Remedy: Re-install OS-9.
------------------------------
Code: 2100EDB6
Display:
Used by:
Cause: The temporary file to display the Part Data could not be opened.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100EDD0
Display:
Used by:
Cause: The start-up parameters are incorrect.
Remedy: Correct the input command if this error occurred due to a direct command. Contact Fuji if the
error did not occur due to a direct command.
------------------------------
第 2096 页
Code: 2100EDD1
Display:
Used by:
Cause: The Part Sort table was not found.
Remedy: Check that the file exists.
------------------------------
Code: 2100EDD2
Display:
Used by:
Cause: The Part Data file (H0/DATA/part.data) does not exist.
Remedy: The Translator cannot run because the Part data file does not exist.
------------------------------
Code: 2100EDD3
Display:
Used by:
Cause: The Part Sort table could not be opened.
Remedy: Check the file.
------------------------------
Code: 2100EDD4
Display:
Used by:
Cause: The Part Data could not be opened.
Remedy: Check that the file exists.
------------------------------
Code: 2100EDD5
Display:
Used by:
Cause: A Part data file with the same name already exists in MCS/1.
Remedy: Set the overwrite protect to YES to replace the contents of the existing file, or specify a new file
name.
------------------------------
Code: 2100EDD6
Display:
Used by:
Cause: The data could not be translated into MCS/1 Part data.
Remedy: Re-execute the function.
------------------------------
Code: 2100EDD7
Display:
Used by:
Cause: The MCS/2 Part data input file does not exist.
Remedy: The Translator cannot run as the Part data file does not exist.
------------------------------
Code: 2100EDD8
Display:
Used by:
Cause: The MCS/2 Part data input file could not be read.
Remedy: Make sure that the contents of the file are correct.
------------------------------
Code: 2100EDD9
Display:
第 2097 页