FUJI错误代码查询.pdf - 第674页

------------------------------ Code: 12068488 Display: TZ-axis: Motor/servo capacity mismatch. Used by: QP3,NP2 Cause: Remedy: Check that the motor and servo amplifier are connected correctly. ---------------------------…

100%1 / 5282
Cause:
Remedy:
------------------------------
Code: 12068480
Display: TZ-axis: Overload warning.
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068481
Display: TZ-axis: Regeneration overload warning.
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068482
Display: TZ-axis: User constant setting warning.
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068483
Display: TZ-axis: MECHATROLINK command warning.
Used by: QP3,NP2
Cause:
Remedy: Check if the digital operator is still connected to a servo amplifier.
------------------------------
Code: 12068484
Display: TZ-axis: MECHATROLINK communication error warning.
Used by: QP3,NP2
Cause:
Remedy: Check that the MECHATROLINK communications cable between the MTU controller and servo
amplifier is connected correctly.
------------------------------
Code: 12068485
Display: TZ-axis: User constant corruption error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068486
Display: TZ-axis: Main circuit detection error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068487
Display: TZ-axis: A parameter setting error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
第 673 页
------------------------------
Code: 12068488
Display: TZ-axis: Motor/servo capacity mismatch.
Used by: QP3,NP2
Cause:
Remedy: Check that the motor and servo amplifier are connected correctly.
------------------------------
Code: 12068489
Display: TZ-axis: Overcurrent error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 1206848A
Display: TZ-axis: Regeneration error!
Used by: QP3,NP2
Cause:
Remedy: Check that the regenerative resistance wiring is connected to the servo amplifier.
------------------------------
Code: 1206848B
Display: TZ-axis: Regeneration overload.
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 1206848C
Display: TZ-axis: Overvoltage error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 1206848D
Display: TZ-axis: Insufficient voltage error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 1206848E
Display: TZ-axis: Excess travel speed error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 1206848F
Display: TZ-axis: Overload peak error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068490
Display: TZ-axis: Structural overload error!
第 674 页
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068491
Display: TZ-axis: DB overload error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068492
Display: TZ-axis: Surge current limit resistor overload.
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068493
Display: TZ-axis: Heat sink overheating error!
Used by: QP3,NP2
Cause: Servo amp error.
Remedy: Reset the servo amp.
------------------------------
Code: 12068494
Display: TZ-axis: Absolute encoder backup error!
Used by: QP3,NP2
Cause:
Remedy: It is necessary to set up the absolute encoder.After the setup is complete, remeasure the
calibration data.
------------------------------
Code: 12068495
Display: TZ-axis: Absolute encoder checksum error!
Used by: QP3,NP2
Cause:
Remedy: It is necessary to set up the absolute encoder.After the setup is complete, remeasure the
calibration data.
------------------------------
Code: 12068496
Display: TZ-axis: Absolute encoder battery error!
Used by: QP3,NP2
Cause:
Remedy: With the servo amplifier power on, check the battery connection.
------------------------------
Code: 12068497
Display: TZ-axis: Absolute encoder data error!
Used by: QP3,NP2
Cause:
Remedy: Without removing the absolute encoder cable, check the cabling surrounding the encoder, and
fix if necessary.
------------------------------
Code: 12068498
Display: TZ-axis: Absolute encoder excess speed error!
第 675 页