FUJI错误代码查询.pdf - 第542页

Remedy: Press the reset button at servo box 3. ------------------------------ Code: 12052109 Display: Servo Not Ready(CP5) Servo system error!(NP2,QP3) Used by: Cause: The servo board is not ready. Servo system error!(NP…

100%1 / 5282
Cause: A cycle alarm has occurred for servo axis SX or SY. The servo axis did not reach the targeted
value within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052103
Display: "Cycle alarm: servo X or Y or Q" (IP)
Servo system error!(NP2,QP3)
Used by: IP1
Cause: A cycle alarm has occurred for servo axis X, Y, or Q.The servo axis did not reach the targeted
value within the expected time. This error may be caused by interference from another object.
Failed to arrive at target position.(NP2,QP3)
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
Make sure that the servo is not overloaded. Inspect the motors and wiring for the motors and servo amp.
Inspect the servo amp. Remove any interfering objects.
Check whether something is interfering with servo axis movement. (NP2, QP3)
------------------------------
Code: 12052104
Display: "Cycle alarm: servo X or Q" (IP)
Used by: IP1
Cause: A cycle alarm has occurred for servo axis X or Q.The servo axis did not reach the targeted value
within the expected time. This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052105
Display: "Cycle alarm: servo X2 or Y" (IP)
Used by: IP2
Cause: A cycle alarm has occurred for servo axis X2 or Y. The servo axis did not reach the targeted value
within the expected time.This error may be caused by interference from another object.
Remedy: Make sure the servo is not overloaded. Inspect the connectors and wiring for the motor and
servo amp. Inspect the servo amp. Remove any interfering objects.
------------------------------
Code: 12052106
Display: Check Servo BOX1
Used by: CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GSP5,GP2,GP3,GP551,GP6,IP3,QP132
Cause: A servo alarm has occurred.
Remedy: Press the reset button at servo box 1.
------------------------------
Code: 12052107
Display: Check Servo BOX2
Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,Cp65,CP652C,CP642,CP643
Cause: A servo alarm has occurred.
Remedy: Press the reset button at servo box 2.
------------------------------
Code: 12052108
Display: Check Servo BOX3
Used by: CP5
Cause: A servo alarm has occurred.
第 541 页
Remedy: Press the reset button at servo box 3.
------------------------------
Code: 12052109
Display: Servo Not Ready(CP5)
Servo system error!(NP2,QP3)
Used by:
Cause: The servo board is not ready.
Servo system error!(NP2,QP3)
Remedy: Cut the power supply and reboot the machine.
Turn the power to the machine off and restart the machine.(NP2,QP3)
------------------------------
Code: 12052110
Display: Servo amp Alarm
Used by:
CP4,CP42,CP43,CP6,CP6M,CP65,CP652C,CP642,CP642M,CP643,NP132.NP133,NP134,NP153,NP2,QP3
Cause: The servo amp is not functioning correctly.
Remedy: Check the servo amp.
------------------------------
Code: 12052111
Display: 软件限位范围外
Used by: NP2,QP3,NP133,NP134,NP153,GPX,NXTP
Cause: 参数部所显示的轴的移动目的值超出了固有值的移动范围。
Remedy: 请确认移动目的位置及固有值的能够移动的范围。
------------------------------
Code: 12052112
Display: A deviation overflow error occurred.
Used by: NP2,QP3
Cause: The target position for the axis displayed in the parameter section falls outside the travel range.
Remedy: Check the target position or travel range specified in machine calibration data.
------------------------------
Code: 12052113
Display: Z-axis positioning error!
Used by: NP2,QP3
Cause: Z-axis movement was aborted due to an error.
Remedy: Check if Z-axis movement is particularly heavy and check for servo amp errors.
------------------------------
Code: 12054001
Display: Plt Unclamp Error DF
Used by: CP5
Cause: Unclamp error at the DF axis pallet.
Remedy: Check the movement of the DF axis pallet clamp, and check the lower edge.
------------------------------
Code: 12054002
Display: Plt Unclamp Error DR
Used by: CP5
Cause: Unclamp error at the DR axis pallet.
Remedy: Check the movement of the DR axis pallet clamp, and check the lower edge.
------------------------------
Code: 12054003
Display: "Pallet IN stn stopper error"
Used by: CP5
第 542 页
Cause: The machine attempted to move the pallet in the IN station, the stopper has not been turned off.
Remedy: Make sure that both the stopper is functioning normally. Check the stopper OFF limit sensor.
------------------------------
Code: 12054004
Display: "Pallet clamp error: DF IN stn"
Used by: CP5
Cause: The DF-axis has failed to clamp a pallet at the pallet IN station.
Remedy: Make sure the DF-axis pallet clamp is functioning normally. Check the upper limit and clamp
check sensors.
------------------------------
Code: 12054005
Display: "Pallet clamp error: DR IN stn"
Used by: CP5
Cause: The DR-axis failed to clamp a pallet at the pallet IN station.
Remedy: Make sure the DR-axis pallet clamp is functioning normally. Check the upper limit and clamp
check sensors.
------------------------------
Code: 12054006
Display: CHECK CLUTCH
Used by: CP3,CP4-1,CP4-2
Cause: There was a clutch movement alarm (CP3).
Remedy: Check the clutch.
------------------------------
Code: 12054007
Display: "Cycle alarm: carrier" (IP)
Used by: IP1
Cause: A problem has occurred in the tray component carrier cylinder system.
Remedy: Adjust the carrier cylinder so that it is capable of moving forward and retracting. Confirm that
the carrier's forward end and retract end sensors are functioning normally.
------------------------------
Code: 12054008
Display: "Cycle alarm: sub nozzle" (IP)
Used by: IP1
Cause: A problem has occurred in the subrobot nozzle cylinder system.
Remedy: Adjust the subrobot nozzle cylinder so that it is capable of moving up and down. Confirm that
the subrobot nozzle's upper and lower limit sensors are functioning normally.
------------------------------
Code: 12054009
Display: Cycle Alarm Tray Remover
Used by: IP1
Cause: There was a tray removal cylinder alarm.
Remedy: Adjust the advanced and retracted positions of the tray removal cylinder.
------------------------------
Code: 1205400A
Display: Cycle Alarm Error conveyor
Used by: IP1,IP2,IP3
Cause: There was a rejected parts conveyor alarm.
Remedy: Adjust the operating ability of the rejected parts conveyor motor.
------------------------------
Code: 1205400B
Display: "Cycle alarm: feeder" (IP,IP2)
第 543 页