FUJI错误代码查询.pdf - 第220页

------------------------------ Code: 11082341 Display: Illegal Part is Sub Nozzle (Remove Part) Used by: MTU4 Cause: This error occurs when the machine judges that there is an undefined part on the sub-nozzle (for exampl…

Code: 11082310

Display: Pickup Recovery Counter Limit Reached

Used by: MTU3,MTU4,MTU5

Cause: The sub-nozzle was unable to pick up a part in the tray and therefore reattempted to pick up the

part the specified number of times, again without success.

Remedy: Check that the tray is correctly positioned and that the parts with in the tray are correctly

positioned. Also check that correct data has been specified in part data.

------------------------------

Code: 11082330

Display: Nozzle Selection Error

Used by: MTU4

Cause: A nozzle which cannot be used on the MTU was specified.

Remedy: Reset the error at the IP machine. If the error occurs repeatedly, contact Fuji.

------------------------------

Code: 11082331

Display: Y Axis Deceleration Sensor is Not ON at Nozzle change

Used by: MTU4

Cause: When an attempt was made to change a nozzle, the Y axis speed reduction sensor was not on.

Remedy: Adjust the Y axis speed reduction sensor and the dog. In addition check that suitable data has

been entered for the MTU Proper data item Carrier_Position_SY.

------------------------------

Code: 11082332

Display: Z Axis Deceleration Sensor is Not ON at Nozzle change

Used by: MTU4

Cause: When an attempt was made to change a nozzle, the Z axis speed reduction sensor was not on.

Remedy: Adjust the Z axis speed reduction sensor and the dog. In addition check that suitable data has

been entered for the MTU Proper data item Parts_Pos_Zt0.

------------------------------

Code: 11082333

Display: Nozzle Pos. Sensor Error

Used by: MTU4

Cause: When the nozzle rotated, the nozzle position sensors did not turn on at the correct positions.

Remedy: Check the nozzle position sensors and the dogs.

------------------------------

Code: 11082334

Display: Nozzle Changer is Not at Retract Limit Position

Used by: MTU4

Cause: During nozzle change, the nozzle changer retract end sensor was not on.

Remedy: Adjust the nozzle changer retract end and advance end sensors.

------------------------------

Code: 11082335

Display: Nozzle Changer is Not at Forward Limit Position

Used by: MTU4

Cause: During nozzle change, the nozzle changer advance end sensor was not on.

Remedy: Adjust the nozzle changer advance end sensor and the dog.

------------------------------

Code: 11082340

Display: Parts Dropped From Sub-Nzl (Remove Part)

Used by: MTU4

Cause: A part picked up by the sub-nozzle was dropped while the Z axis was ascending.

Remedy: Remove the part which was dropped.

第 219 页

------------------------------

Code: 11082341

Display: Illegal Part is Sub Nozzle (Remove Part)

Used by: MTU4

Cause: This error occurs when the machine judges that there is an undefined part on the sub-nozzle (for

example, the operator may have intentionally placed a part on the sub-nozzle).

Remedy: If there is a part on the sub-nozzle, remove it. Furthermore, check the part detection sensor.

------------------------------

Code: 11082350

Display: Part Not Been Transferred From Sob-nozzle to Carrier

Used by: MTU4

Cause: A picked part was dropped while the Z axis was moving from its ascent position to the position

where the part is placed on the carrier.

Remedy: Remove the part which was dropped

------------------------------

Code: 11082351

Display: Part Dropped During Carrier Movement (Remove Part)

Used by: MTU4

Cause: The part being moved into the machine by the carrier fell off the carrier.

Remedy: Remove the part which fell.

------------------------------

Code: 11082352

Display: Part Pusher Up Limit Sensor is Not ON

Used by: MTU4

Cause: When the clamp installed at the carrier 2nd position was raised, the up sensor did not come on.

Remedy: Check that air is being supplied and that the clamp mechanism and up sensor are functioning

normally.

------------------------------

Code: 11082353

Display: Part Pusher Down Limit Sensor is Not ON

Used by: MTU4

Cause: When the clamp installed at the carrier 2nd position was lowered, the down sensor did not come

on.

Remedy: Check that air is being supplied and that the clamp mechanism and down sensor are

functioning normally.

------------------------------

Code: 11082354

Display: Illegal Part is On Carrier (Remove Parts On Carrier)

Used by: MTU4

Cause: This error occurs when the machine judges that there is an undefined part on the carrier (for

example, the operator may have intentionally placed a part on the carrier).

Remedy: If there is a part on the carrier, remove it. Furthermore, check the part detection sensors at the

1st and 2nd positions.

------------------------------

Code: 11082355

Display: Carrier No.2 Pos. is In Part Data In Spite of No Part Pusher

Used by: MTU4

Cause: This error occurs if the 5th bit in the MTU4 Proper data item Machine_status is set to 0 (

indicating that the part clamp is not fitted), but in part data the 2nd position is specified.

Remedy: Check that there are no parts for which Carrier_select in part datais set to 1 (the 2nd position

setting) and that even if the parts clamp is installed, the 5th bit from the right in Machine_status is set to

第 220 页

------------------------------

Code: 11082360

Display: Waffle Tray Overloaded Remove Part

Used by: MTU4

Cause: Too many waffle trays have been stacked up.

Remedy: Remove the overstacked waffle trays.

------------------------------

Code: 11082370

Display: Reject Tray Box Full

Used by: MTU4

Cause: This error occurs when discarded trays accumulate, causing the sensor beam to be cut for a

continued period of time.

Remedy: Remove the accumulated trays. Check the adjustment of the sensors. Check that there are no

other objects in the tray area.

------------------------------

Code: 11082380

Display: Tray Reject Error

Used by: MTU4

Cause: This error occurs when a tray which is to be ejected is released at the eject position but the eject

sensor does not detect the falling tray.

Remedy: If the tray cannot be picked up, adjust the tray pick up point set in part data's Tray_pickup_pnt

and check that the tray can be picked up. Furthermore, if this error occurs even when the tray is picked

up, check the sensor.

------------------------------

Code: 11082390

Display: Tray Plate Setting Error

Used by: MTU4

Cause: The tray plate set sensor was activated while the T axis was moving.

Remedy: Check that the tray plate door is not open and that the tray plate is firmly positioned.

------------------------------

Code: 110823A0

Display: No Tray

Used by: MTU4

Cause: There are no trays but manual tray positioning was attempted.

Remedy: Supply trays.

------------------------------

Code: 110823B0

Display: Tray Space Chk Sens. Not ON

Used by: MTU4

Cause: The robot safety sensor was not on when the Y axis moved to pick up a tray part or to eject a

tray.

Remedy: Check the robot safety sensor and the dog. Also check that a suitable value is entered for the

MTU Proper data item Origin_Position_T0 to ensure that the T axis origin is at the correct position.

------------------------------

Code: 110823C0

Display: Tray Number Internal Error

Used by: MTU3,MTU4,MTU

Cause: During tray positioning, an abnormal tray number was detected.

Remedy: Initialize the memory.

------------------------------

第 221 页