FUJI错误代码查询.pdf - 第1161页
Remedy: ------------------------------ Code: 15040B10 Display: Used by: Cause: Remedy: ------------------------------ Code: 15040B11 Display: Used by: Cause: Remedy: ------------------------------ Code: 15040B12 Display:…
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B08
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B09
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B0A
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B0B
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B0C
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B0D
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B0E
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B0F
Display:
Used by:
Cause:
第 1160 页
Remedy:
------------------------------
Code: 15040B10
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B11
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040B12
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040C01
Display: 电路板位置异常 往复臂Ｌ
Used by: NXTP
Cause: 搬送处有不明的电路板。
Remedy: 请除去电路板再次放入。
<img src="$LKEY_ERRIMG_MC$/15040C01.PNG">
------------------------------
Code: 15040C02
Display: 电路板位置异常 往复臂Ｒ
Used by: NXTP
Cause: 搬送处有不明的电路板。
Remedy: 请除去电路板再次放入。
<img src="$LKEY_ERRIMG_MC$/15040C02.PNG">
------------------------------
Code: 15040C03
Display: 下道工序电路板搬送异常 往复臂Ｌ
Used by: NXTP
Cause: 向下道工序的搬运电路板时发生了异常。复臂L搬运轨道的电路板排出到了下道工序，不过，在下道工序不能
进行正常地电路板的搬运，在规定时间(15秒)里从下道工序的电路板来的要求信号没有OFF。
Remedy: 请调整下道工序的搬运轨道宽度以使电路板流动顺畅。
<img src="$LKEY_ERRIMG_MC$/15040C03.PNG">
------------------------------
Code: 15040C04
Display: 下道工序电路板搬运异常 往复臂Ｒ
Used by: NXTP
Cause: 向下道工序的搬运电路板时发生了异常。复臂R搬运轨道的电路板排出到了下道工序，不过，在下道工序不能
进行正常地电路板的搬运，在规定时间(15秒)里从下道工序的电路板来的要求信号没有OFF。
Remedy: 请调整下道工序的搬运轨道宽度以使电路板流动顺畅。
<img src="$LKEY_ERRIMG_MC$/15040C04.PNG">
------------------------------
Code: 15050101
第 1161 页
Display: Emergency Stop
Used by:
Cause: The emergency stop button was pressed (if peripherals were being used, the safety door was
open).
Remedy: After resetting the emergency stop button (or closing the safety door), press the reset button.
------------------------------
Code: 15050201
Display: Conveyor Overtravel
Used by:
Cause: The conveyor width overtravel sensor was activated.
Remedy: Inch the conveyor to where the overtravel sensor is off, and press the reset button to cancel this
alarm (on the LCD terminal, press the Start/Over key).
------------------------------
Code: 15050202
Display: Follow-up Error
Used by:
Cause: Follow-up had not yet been finished, and the overtravel sensor was activated. During follow-up,
the board arrival sensor and the borad pass switch were activated (a board is on the conveyor).
Remedy: Inch the conveyor so that the width widens, and press the reset button (on the LCD terminal,
press the Start/Over Key). If there is a board on the conveyor, remove it. Check that the board arrival
sensor is not being activated by something other than a board, and adjust the sensor volume. Then, when
the board arrival sensor is off, press the reset button to cancel the alarm (on the LCD terminal, press the
Start/Over key).
------------------------------
Code: 15050203
Display: Transport Error
Used by:
Cause: The board flowing on the conveyor got caught.
Remedy: Set the board so that it can flow smoothly, and press the reset button to cancel the alarm (on
the LCD terminal, press the Start/Over Key).
------------------------------
Code: 15502100
Display:
Used by:
Cause: There was a main conveyor board check sensor alarm, or the sensor is not adjusted properly.
Remedy: Remove the board by hand. If production has finished, unload the board to the out conveyor. If
it has not finished, put the board back on the in conveyor.
------------------------------
Code: 1601??08
Display: An error occurred for the PFU/MFU cutter.
Machine type: QP3
Used by:
Cause: PFU/MFU tape cutter error. The tape box may not be set correctly.
The feeder slot number is contained in the fifth and sixth digit of the error code (hexadecimal
notation).
Remedy: Check the tape cutter and tape on the PFU/MFU in question.
Check the tape box is set correctly.
------------------------------
Code: 1601000F
Display: STU tray supply time out
Used by: NP2,QP3
第 1162 页