FUJI错误代码查询.pdf - 第511页

------------------------------ Code: 1205030C Display: Servo error PO-axis:Over travel Used by: QP132 Cause: The PO-axis is in overtravel. Remedy: Correct the position of the PO-axis using the inching keys. -------------…

------------------------------

Code: 12050304

Display: "Servo alarm: X-axis overtravel" (CP4,CP6) "Servo alarm: Y-axis overtravel" (CP43)

Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GSP5

Cause: The X-axis has overtraveled. The Y-axis has overtraveled.(CP43)

Remedy: Inch the X-axis to cancel the overtravel. Inch the Y-axis to cancel the overtravel.(CP43)

------------------------------

Code: 12050305

Display: "Servo alarm: Y-axis overtravel" (CP4,CP6) "Servo alarm: Z-axis overtravel" (CP43)

Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GSP5

Cause: The Y-axis has overtraveled. The Z-axis has overtraveled.(CP43)

Remedy: Inch the Y-axis to cancel the overtravel. Inch the Z-axis to cancel the overtravel.(CP43)

------------------------------

Code: 12050306

Display: "Servo alarm: Z-axis overtravel" (CP4,CP6) "Servo alarm: D1-axis overtravel" (CP43)

Used by: CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GSP5

Cause: The Z-axis has overtraveled. The D1-axis has overtraveled.(CP43)

Remedy: Inch the Z-axis to cancel the overtravel. Inch the D1-axis to cancel the overtravel.(CP43)

------------------------------

Code: 12050307

Display: "Servo alarm: D1-axis overtravel" (CP4,CP6) "Servo alarm: D2-axis overtravel" (CP43) "Servo

alarm: DF-axis overtravel" (CP652C)

Used by: CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GSP5

Cause: The D1-axis has overtraveled. The D2-axis has overtraveled.(CP43) The DF-axis has

overtraveled.(CP652C)

Remedy: Inch the D1-axis to cancel the overtravel.Inch the D2-axis to cancel the overtravel.(CP43) Inch

the DF-axis to cancel the overtravel.(CP652C)

------------------------------

Code: 12050308

Display: "Servo alarm: D2-axis overtravel" (CP6) "Servo alarm: DR-axis overtravel" (CP652C)

Used by: CP5,CP6,CP6M,CP65,CP652C,CP642,CP643

Cause: The D2-axis has overtraveled. The DR-axis has overtraveled.(CP652C)

Remedy: Inch the D2-axis to cancel the overtravel. Inch the DR-axis to cancel the overtravel.(CP652C)

------------------------------

Code: 12050309

Display: Servo error SS-axis:Over travel

Used by: QP132

Cause: The SS-axis is in overtravel.

Remedy: Correct the position of the SS-axis using the inching keys.

------------------------------

Code: 1205030A

Display: Servo error MX-axis:Over travel

Used by: QP132

Cause: The MX-axis is in overtravel.

Remedy: Correct the position of the MX-axis using the inching keys.

------------------------------

Code: 1205030B

Display: Servo error MY-axis:Over travel

Used by: QP132

Cause: The MY-axis is in overtravel.

Remedy: Correct the position of the MY-axis using the inching keys.

第 510 页

------------------------------

Code: 1205030C

Display: Servo error PO-axis:Over travel

Used by: QP132

Cause: The PO-axis is in overtravel.

Remedy: Correct the position of the PO-axis using the inching keys.

------------------------------

Code: 1205030D

Display: Y-axis collision!

Used by: NP2,QP3

Cause: The Y-axis collision sensor has been triggered. There is interference between the Y1 and Y2

axis.(NP2,QP3)

Remedy: Use the inching keys to clear the interference.(NP2,QP3)

------------------------------

Code: 1205030E

Display: 往复臂 O.T.异常

Used by: NXTP

Cause: 往复臂的移动目标值为范围外，从属搬运轨道越过超程传感器。

Remedy: 请向前侧移动，解除传感器。

------------------------------

Code: 1205031?

Display: Servo Ararm ? axis. Overtravel. (CP6)

Used by:

Cause: Overtravel error at the ? axis.

Remedy: Use inching to clear the overtravel condition.

------------------------------

Code: 12050311

Display: 伺服报错超程

Used by: GPX-C

Cause: 显示位置上发生超程现象。

Remedy: 请使用微操作或手操作解除超程现象。

------------------------------

Code: 12050401

Display: 内存备份不良 Memory Backup NG (IP,IP2,GSP)

Used by: GPX,IP, IP2, GSP,NXTP

Cause: 有效的Proper和Status没有被传输。

Remedy: 请传输Proper和Status。此时，在传输Proper和Status后，暂时关闭电源然后重新接通。（有可能伺服的

动作不正常)在每次接通电源后发生时，请检查备份用的电池。进行了复位后也会显示该错误。

------------------------------

Code: 12050402

Display: "Data Transmission Line NG" (IP, GL), "Transmiterr" (CP3)

Used by: GL2

Cause: The machine cannot transmit data to the MCS-16. The memory buffer has become full due to a

failure in communication with the MCS-16.

Remedy: Check the communication cable. Make sure the MCS-16 is not hung up.

------------------------------

Code: 12050403

Display: MFU1 (2) is not ready

Used by: IP2

第 511 页

Cause: MFU has not been set.

Remedy: Set the MFU.

------------------------------

Code: 12050404

Display: "Remove D1-3" (IP2)

Used by:

Cause: A tape feeder or stick feeder has been attached to D1, D2, or D3 on an FIP-series machine

equipped with an MTU.

Remedy: Remove tape feeders and stick feeders from D1, D2, and D3.

------------------------------

Code: 12050405

Display: "Thermal alarm" (GSP, GL, CP5), "PCM THERMAL Alarm" (CP651C)

Used by: CP4-1,CP4-2,CP4-

3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GSP2,GSP3,GSP5,GP2,GP3,GP551,GP6,IP1,IP3,QP132

Cause: A servo motor thermal relay has been tripped.On the CP651C, an alarm has been detected by a

thermal relay on one of the following motors: UP elevator, DOWN elevator, or return conveyor.

Remedy: Make sure the servo axes are not overloaded. Inspect the connectors and wiring for motors and

servo amps. Press the thermal relay's reset button to cancel the error.

------------------------------

Code: 12050406

Display: Ready For Program NG

Used by:

Cause: A program has not been transmitted.

Remedy: Transmit a program from MCS.

------------------------------

Code: 12050407

Display: " 冷却装置警告 ", " Cooler Alarm "(GSP,GL)

Used by: GL2,GSP2,GSP3,GP2,GP3,GPX,NXTP

Cause: 超出了温调用的操作画面上所设定的温度调整的范围。

Remedy: 请确认温调用的开关是否开启。如果开关开启着，请检查加热器和冷却装置是否发生了异常，另外，温度调

整范围的设定是否正确。

------------------------------

Code: 12050408

Display: " 加热器警告 ", " Heater Alarm "(GSP,GL)

Used by: GL2,GSP2,GSP3,GP2,GP3,GPX,NXTP

Cause: 超出了温调用的操作画面上所设定的温度调整的范围。

Remedy: 请确认温调用的开关是否开启。如果开关开启着，请检查加热器和冷却装置是否发生了异常，另外，温度调

整范围的设定是否正确。

------------------------------

Code: 12050409

Display: "Zero Set NG"

Used by:

Cause: Zero setting has not been performed.

Remedy: Perform zero setting.If the machine has stopped part of the way through zero setting after the

START button is pressed, the display will indicate which axes have not been zeroed. Press

theEMERGENCY STOP button, turn off the power supply, and check the axes in question for

abnormalities. (Check the zero-setting sensors, motors, cables, and amps; check for mechanical

interference; etc.)

------------------------------

第 512 页