FUJI错误代码查询.pdf - 第1121页
(X0C2) did not deactivate (OFF ) within the specified time limit. Remedy: Check that the stopper is functioning properly. If the error continues, check that both of the sensors带幨X0C1, X0C2带幩ar e functioning properly. ---…
Display: In-carrier clamp limit and unclamp limit sensor logic error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: In-carrier clamp limit and unclamp limit sensor logic error.
Remedy: Verify that all sensors (X0B7 to X0BE) are operating properly.
------------------------------
Code: 15040234
Display: IN 1 stopper error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: The IN 1 stopper ON sensor failed to switch on. Although the IN 1 stopper was switched off, the
OFF limit sensor failed to switch on within the prescribed period of time (3 secs.).
Remedy: Check to see if the stopper is operating smoothly. If operation is smooth, but the error occurs
anyway, check to see if the sensors (X0C1, X0C2) are operating properly.
------------------------------
Code: 15040235
Display: In-conveyor panel set error.
Used by: CP-732E, CP-742ME, CP-742E
Cause: When the in-conveyor 1 stopper was raised, the in-conveyor 1 panel arrival sensor switched from
on to off.
Remedy: Check the panel conveyance condition. The first panel which is already on the in-conveyor may
have been pushed upward out of position.
------------------------------
Code: 15040236
Display: In-conveyor panel conveyance error
Used by: CP-752E
Cause: The panel passed through the in-conveyor panel speed reduction sensor (X0AB) however, it was
not detected by the panel
arrival check sensor (X0AC) within the specified time limit.
Remedy: Check that the in-conveyor panel arrival check sensor is functioning properly and confirm the
panel status.
------------------------------
Code: 15040237
Display: In-conveyor panel conveyance error
Used by: CP-752E
Cause: An attempt was made to transfer the panel from the in-conveyor to the main-conveyor however,
the in-conveyor panel spee
d reduction sensor (X0AB) or the panel arrival check sensor (X0AC) did not deactivate (OFF) within the
specified time limit.
Remedy: Check that the in-conveyor panel speed reduction and panel arrival check sensors are
functioning properly and confirm t
he panel status.
------------------------------
Code: 15040238
Display: In-conveyor Stopper Error
Used by: CP-752E
Cause: One of the following errors has occurred:
The machine output the "lower stopper" signal, however the stopper lower end sensor (X0C2) did not
activate (ON).
oth the in-conveyor stopper upper end sensor (X0C1) and the in-conveyor stopper lower end sensor (X0C2)
did not activate (ON) wi
thin the specified time limit.
Both the in-conveyor stopper upper end sensor (X0C1) and the in-conveyor stopper lower end sensor
第 1120 页
(X0C2) did not deactivate (OFF
) within the specified time limit.
Remedy: Check that the stopper is functioning properly. If the error continues, check that both of the
sensors带幨X0C1, X0C2带幩ar
e functioning properly.
------------------------------
Code: 15040239
Display: In-conveyor panel conveyance error
Used by: CP-752E
Cause: The in-conveyor panel arrival sensor (X0AC) was activated (ON) before the panel speed reduction
sensor (X0AB).
Remedy: Check that the in-conveyor panel speed reduction sensor is functioning properly and confirm the
panel status.
------------------------------
Code: 1504023A
Display: 电路板位置异常 载入侧搬运轨道
Used by: GPX,NXTP
Cause: 在载入侧搬运轨道无法搬运的位置上有电路板。
Remedy: 请除去电路板然后重新放入。
<img src="$LKEY_ERRIMG_MC$/EI0001.bmp">
------------------------------
Code: 1504023B
Display: 载入搬运轨道有电路板错误
Used by: NXTP
Cause: 因为在载入搬运轨道上有电路板，所以不进入到下一步的处理。
Remedy: 请清除电路板。
<img src="$LKEY_ERRIMG_MC$/1504023B.PNG">
------------------------------
Code: 1504023C
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 1504023D
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 1504023E
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 1504023F
Display:
Used by:
Cause:
Remedy:
第 1121 页
------------------------------
Code: 15040240
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040241
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040242
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040243
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 15040301
Display: PCB Loading NG
CHECK PCB
CHECK MAIN-CONVEYOR
Used by: CP3,GSP2,GSP3,IP2,NXTP
Cause: The board cannot be loaded properly.
Remedy: Place the board in its correct position. Check the movement of the stopper at the I/O display
OUT2-26 B_STOPPER_OFF and IN5-19 IN_STOPPER_SW.
------------------------------
Code: 15040302
Display: CHECK LOADER
Used by: CP3
Cause: The loader is not in its original position.
Remedy: Return the loader to its original position.
------------------------------
Code: 15040303
Display: Duplex Loading
Used by: GSP2,GSP3
Cause: Two boards were loaded. The appropriate sensor is connected to IN2-12 DOUBLE_PCB.
Remedy: Remove the boards.
------------------------------
Code: 15040304
Display: Cycle Alarm CLAMP(GSP2)
CYCLE NG Lifter(IP2)
Clamp Error(IP1)
PCB lifter error!(NP2,QP3)
第 1122 页