FUJI错误代码查询.pdf - 第2067页

Used by: Cause: Either the specified part data has been corrupted or the specified file is not in the Fuji format. Remedy: Using the editor, check the part data. ------------------------------ Code: 2100CA21 Display: GD …

100%1 / 5282
Cause: Either there is no work directory or there is insufficient RAM.
Remedy: Reboot the MCS.
------------------------------
Code: 2100CA19
Display: Sample file open error
Used by:
Cause: Either there is no work file or it has been corrupted.
Remedy: Quit and then re-open the sample file.
------------------------------
Code: 2100CA1A
Display: Sample file read error
Used by:
Cause: Either there is no work file or it has been corrupted.
Remedy: Quit and then re-open the sample file.
------------------------------
Code: 2100CA1B
Display: Sample file write error
Used by:
Cause: Either there is no work file or it has been corrupted.
Remedy: Quit and then re-open the sample file.
------------------------------
Code: 2100CA1C
Display: Header read error
Used by:
Cause: Either the specified production program has been corrupted or the specified file is not in the Fuji
format.
Remedy: Using the editor, check the production program.
------------------------------
Code: 2100CA1D
Display: Offset read error
Used by:
Cause: Either the specified production program has been corrupted or the specified file is not in the Fuji
format.
Remedy: Using the editor, check the production program.
------------------------------
Code: 2100CA1E
Display: Program file open error
Used by:
Cause: Either the specified production program has been corrupted or the specified file is not in the Fuji
format.
Remedy: Using the editor, check the production program.
------------------------------
Code: 2100CA1F
Display: Program file read error
Used by:
Cause: Either the specified production program has been corrupted or the specified file is not in the Fuji
format.
Remedy: Using the editor, check the production program.
------------------------------
Code: 2100CA20
Display: PD file open error
第 2066 页
Used by:
Cause: Either the specified part data has been corrupted or the specified file is not in the Fuji format.
Remedy: Using the editor, check the part data.
------------------------------
Code: 2100CA21
Display: GD file open error
Used by:
Cause: Either the specified GD data has been corrupted or the specified file is not in the Fuji format.
Remedy: Using the editor, check the GD data.
------------------------------
Code: 2100CA22
Display: Nozzle file open error
Used by:
Cause: Either the specified nozzle assignment table has been corrupted or the specified file is not in the
Fuji format.
Remedy: Using the editor, check the nozzle assignment table.
------------------------------
Code: 2100CA23
Display: Pallet file open error
Used by:
Cause: Either the specified pallet data has been corrupted or the specified file is not in the Fuji format.
Remedy: Using the editor, check the pallet data.
------------------------------
Code: 2100CA24
Display: Format error
Used by:
Cause: The format command cannot be started.
Remedy: Re-install the operating system.
------------------------------
Code: 2100CA25
Display: Input file name doesn't exist
Used by:
Cause: The production program name was not specified.
Remedy: Specify the production program name.
------------------------------
Code: 2100CA26
Display: File not found
Used by:
Cause: One or more of the data files (PD, GD, NAT, or PLT) which are described in the production
program is missing.
Remedy: If a file is missing, either create the file or make the necessary corrections in the production
program.
------------------------------
Code: 2100CA27
Display: File exists
Used by:
Cause: A file with the same name already exists at the destination.
Remedy: Proceed as the message indicates.
------------------------------
Code: 2100CA28
Display: Same device
第 2067 页
Used by:
Cause: The specified input and output drive are the same.
Remedy: Check the specified drives.
------------------------------
Code: 2100CA29
Display: Media full
Used by:
Cause: The output disk capacity is insufficient.
Remedy: When the output destination is a floppy drive, replace the disk as per the message instructions.
When the output destination is the hard drive, cancel the copy function and secure the needed amount of
memory by erasing any unnecessary files.
------------------------------
Code: 2100DA09
Display: can't load proper file on memory
Used by:
Cause: The specified file could not be loaded into memory.
Remedy: Re-boot MCS. If the error recurs, re-install the system.
------------------------------
Code: 2100E000
Display: Illegal parameter
Used by:
Cause: The start-up command does not contain the correct number of parameters.
Remedy: Correct the parameters if the error occurred when starting up with a direct command.
------------------------------
Code: 2100E001
Display: Illegal parameter
Used by:
Cause: The start-up parameters are incorrect.
Remedy: Correct the input parameters if this error occurred when starting up with a direct command.
------------------------------
Code: 2100E002
Display: Illegal language option
Used by:
Cause: The display language was not specified correctly.
Remedy: Correct the input option if this error occurred when starting up with a direct command.
------------------------------
Code: 2100E003
Display: Illegal terminal option
Used by:
Cause: The terminal number was not specified correctly in the start-up command.
Remedy: Correct the input terminal number if this error occurred when starting up with a direct
command.
------------------------------
Code: 2100E004
Display: Run Level Check error
Used by:
Cause: The Run Level of the start-up command is incorrect.
Remedy: Correct the input Run Level if this error occurred when starting up with a direct command.
------------------------------
Code: 2100E005
Display: Strings file load error
第 2068 页