FUJI错误代码查询.pdf - 第2191页
Display: Nickname specified as filename in flush command. Used by: Cause: A name the same as the nickname cannot be set in the output file specified by the flush command. Remedy: Specify a name other than the nickname fo…
was made to download it to the machine foreground.
Remedy:
------------------------------
Code: 51??0068
Display: Non-deletable program.
Used by:
Cause: Among the programs specified for deletion there is a program which cannot be deleted.
Remedy:
------------------------------
Code: 51??0069
Display: No program.
Used by:
Cause: The program specified for deletion is not in the machine or if several programs have been
specified for deletion, one of them is not in the machine.
Remedy:
------------------------------
Code: 51??0070
Display: Too many programs specified.
Used by:
Cause: Too many programs have been specified for deletion.
Remedy: No more than ten programs can be specified since there are only a maximum of ten programs in
the machine.
------------------------------
Code: 51??0071
Display: Specified machine is a slave.
Used by:
Cause: The machine specified by its nickname is a slave. Production information cannot be acquired
from a slave.
Remedy: Check the nickname and specify a master.
------------------------------
Code: 51??0079
Display: Specified machine does not support the command.
Used by:
Cause: The command cannot be performed because the specified machine does not support it.
Remedy:
------------------------------
Code: 51??0080
Display: Production log acquisition has already ended.
Used by:
Cause: Production data log acquisition for the applicable machine has already been ended with the finish
command.
Remedy: To perform production data log acquisition, it is necessary to restart the C/C.
------------------------------
Code: 51??0081
Display: Real-time process simultaneous start limit exceeded.
Used by:
Cause: For the same machine up to four real-time commands may be started/operated at the same time.
However, an attempt was made to start a fifth real-time command.
Remedy: Check that no real-time commands are being executed at the machine.
------------------------------
Code: 51??0082
第 2190 页
Display: Nickname specified as filename in flush command.
Used by:
Cause: A name the same as the nickname cannot be set in the output file specified by the flush
command.
Remedy: Specify a name other than the nickname for the output file name.
------------------------------
Code: 51??0083
Display: The production data log is being acquired.
Used by:
Cause: The production data log for the target machine is presently being acquired.
Remedy: Use the fi finish command to stop acquisition of the production data log.
------------------------------
Code: 51??0084
Display: The sampled event is not defined.
Used by:
Cause: The sampled event is not recorded in the C/C setting data.
Remedy: None of the items EVENT,REMARK or HLP is recorded in the C/C setting data,therefore the
production data is not sampled.Record the production data which you want to sample in the C/C setting
data.
------------------------------
Code: 51??0090
Display: Error ending machine.
Used by:
Cause: When a single command was executed for a number of machines, a machine which had made an
error stop was discovered. Result codes for each of the machines are reported to the supplementary
information.
Remedy:
------------------------------
Code: 51??0091
Display: Command canceled by operator.
Used by:
Cause: Execution of the command was canceled by the operator.
Remedy:
------------------------------
Code: 51??0092
Display: Non-interruptable command.
Used by:
Cause: The specified job is a command which cannot be interrupted.
Remedy:
------------------------------
Code: 51??0093
Display: Command in interrupt-prohibit status.
Used by:
Cause: Interruption of the specified job is presently prohibited.
Remedy:
------------------------------
Code: 51??0094
Display: Command not supported in present version.
Used by:
Cause: The specified command is not supported in the present C/C.
Remedy: The specified command cannot be used in the present C/C. The command will either be
第 2191 页
supported in the future or it is no longer supported.
------------------------------
Code: 51??0095
Display: Command process could not be started.
Used by:
Cause: The command process in the C/C could not be started.
Remedy: Report the details of this problem to Fuji.
------------------------------
Code: 51??0096
Display: Scheduling failure.
Used by:
Cause: A scheduling failure occurred in the C/C.
Remedy: Report the details of this problem to Fuji.
------------------------------
Code: 51??0097
Display: File acquisition failure.
Used by:
Cause: A file acquisition failure occurred in the C/C.
Remedy: Report the details of this problem to Fuji.
------------------------------
Code: 51??0098
Display: Memory acquisition failure.
Used by:
Cause: A memory acquisition failure occurred in the C/C.
Remedy: Report the details of this problem to Fuji.
------------------------------
Code: 51??0099
Display: Other.
Used by:
Cause: A fatal error occurred in the C/C.
Remedy: Report the details of this problem to Fuji.
------------------------------
Code: 51??0101
Display: The C/C has not been started.
Used by:
Cause: As above.
Remedy: Start the C/C.
------------------------------
Code: 51??0102
Display: The C/C is down.
Used by:
Cause: The C/C stopped operating for one of the following reasons.Ctrl-C was input at the C/C start
window.The C/C start window was closed.The C/C start user logged off.The C/C start machine was shut
down.
Remedy: Start the C/C.
------------------------------
Code: 51??1000
Display: No "UNIT", "PROGRAM" or "UNIT", "PROGRAM" is not at the correct position.
Used by:
Cause: "UNIT", "PROGRAM" was not found in the specified production program or "UNIT", "PROGRAM"
does not follow the correct unit.
第 2192 页