FUJI错误代码查询.pdf - 第1888页
Code: 21006004 Display: separator pipe create error Used by: Cause: Unable to create the separator pipe. Remedy: Re-boot MCS. ------------------------------ Code: 21006005 Display: Permanent Set Table name get error Used…
------------------------------
Code: 21005901
Display: Now edttting data is not Squence data
Used by:
Cause: The cut command was used on data which was not sequence data.
Remedy: Only use the cut command on sequence data.
------------------------------
Code: 21005902
Display: Cut number syntax error
Used by:
Cause: In the cut command "0" or "1" was used. The cut command must use the number "2" or greater.
Remedy: The cut command erases all the sequence data lines greater than the number input. Input "2"
or greater. In sequence data, at least one line is necessary.
------------------------------
Code: 21005903
Display: Input sequence NO. not found.
Used by:
Cause: The sequence number does not exist.
Remedy: Check the sequence data and re-execute the sequence.
------------------------------
Code: 21005950
Display: Edit command not execute
Used by:
Cause: The sub-editor could not handle the overflow.
Remedy: At a terminal there can be up to 2 editors. If a new editor has been opened, try again after
closing the sub-editor.
------------------------------
Code: 21006000
Display: Illegal parameter
Used by:
Cause: The parameter is illegal.
Remedy: Check the parameter.
------------------------------
Code: 21006001
Display: message file read error
Used by:
Cause: The message file could not be read.
Remedy: Re-install the separator software.
------------------------------
Code: 21006002
Display: console pipe open error
Used by:
Cause: Unable to open the console pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21006003
Display: CRT semaphore link error
Used by:
Cause: The CRT semaphore ID could not be obtained.
Remedy: Re-boot MCS.
------------------------------
第 1887 页
Code: 21006004
Display: separator pipe create error
Used by:
Cause: Unable to create the separator pipe.
Remedy: Re-boot MCS.
------------------------------
Code: 21006005
Display: Permanent Set Table name get error
Used by:
Cause: The permanent set table name could not be read from the environment variable file.
Remedy: Check the permanent set table.
------------------------------
Code: 21006006
Display: Special Conditions File name get error
Used by:
Cause: The name specified for the Special Conditions File could not be read from the environment
variables file.
Remedy: Check the Special conditions file.
------------------------------
Code: 21006007
Display: Off-line Descriptor get error
Used by:
Cause: The name specified for the off-line descriptor could not be read from the environment variables
file.
Remedy: Check the off-line descriptor.
------------------------------
Code: 21006008
Display: line name get error
Used by:
Cause: The name specified for the line name could not be read from the environment variables file.
Remedy: Check the line descriptor.
------------------------------
Code: 21006009
Display: generate switch get error
Used by:
Cause: The generate switch could not be read from the environment variables file.
Remedy: Check the environment variables file.
------------------------------
Code: 2100600A
Display: object disk name get error
Used by:
Cause: The object disk could not be read from the environment variables file.
Remedy: Check the environment variables file.
------------------------------
Code: 2100600B
Display: output file name get error
Used by:
Cause: The output file could not be read from the environment variables file.
Remedy: Check the environment variables file.
------------------------------
Code: 2100600C
第 1888 页
Display: original Machine Type Table file open error
Used by:
Cause: The Machine Type Table could not be opened.
Remedy: Re-install the automatic programming software.
------------------------------
Code: 2100600D
Display: compile Machine Type Table file create error
Used by:
Cause: The machine type table work file could not be created.
Remedy: Re-install the Automatic programming software.
------------------------------
Code: 2100600E
Display: compile Machine Type Table file create error
Used by:
Cause: The machine type table workfile could not be opened.
Remedy: Re-install the automatic programming software.
------------------------------
Code: 2100600F
Display: original Machine Type Table file read error
Used by:
Cause: The machine type table workfile could not be read.
Remedy: Re-install the automatic programming software.
------------------------------
Code: 21006010
Display: original Machine Type Table file format error
Used by:
Cause: The machine type table file was not properly formatted.
Remedy: Re-install the automatic programming software.
------------------------------
Code: 21006011
Display: compile Machine Type Table file write error
Used by:
Cause: The machine type table workfile could not be written to.
Remedy: Re-install the software.
------------------------------
Code: 21006012
Display: memory full !
Used by:
Cause: Not enough free memory space remains.
Remedy: Re-boot MCS.
------------------------------
Code: 21006013
Display: Permanent Set Table file not specified in Seperation Conditi
Used by:
Cause: The Permanent Set Table filename has not been specified in the separator.
Remedy: Input the name of the Permanent Set Table file.
------------------------------
Code: 21006014
Display: Off-line Descriptor open error
Used by:
Cause: The Off-line Descriptor could not be opened.
第 1889 页