FUJI错误代码查询.pdf - 第158页

Display: Used by: IP2,IP3 Cause: The value set in Proper Data item "Flux_st1_d_no" or "Flux_st2_d_no" is out of range. Remedy: The valid range for these Proper Data items is 0 to 37 ("0" sig…

Display:

Used by: IP2

Cause: The Proper data item Reducing time Y is less than 30 or greater than 500 (IP2).

Remedy: Enter the correct Proper value and re-transmit the Proper data.

------------------------------

Code: 11022622

Display:

Used by: IP2

Cause: The Proper data item Reducing time Z is less than 30 or greater than 500 (IP2).

Remedy: Enter the correct Proper value and re-transmit the Proper data.

------------------------------

Code: 11022623

Display:

Used by: IP2

Cause: The Proper data item Reducing time Q is less than 30 or greater than 500 (IP2).

Remedy: Enter the correct Proper value and re-transmit the Proper data.

------------------------------

Code: 11022624

Display: ATC POSITION ERROR

Used by: IP2

Cause: The Proper value 64.X_atc_origin_2 is smaller than 35.X_atc_origin (setting was not made).

Remedy: Make the Proper measurement and enter it. This displays only on the IP1 with shift type

nozzles.

------------------------------

Code: 11022630

Display:

Used by: IP2

Cause: Proper data's X_max is smaller than the values X1_ESC and X2_ESC.

Remedy: Input the correct Proper values.

------------------------------

Code: 11022631

Display:

Used by: IP2

Cause: Proper data's X_max is smaller than the values X1_wait and X2_wait.

Remedy: Input the correct Proper values.

------------------------------

Code: 11022632

Display:

Used by: IP2

Cause: Proper data's X_max is smaller than the values Nozzle_check_pos.1 and Nozzle_check_pos.2.

Remedy: Input the correct Proper values.

------------------------------

Code: 11022633

Display: None

Used by: IP2,IP3

Cause: When using the placing pressure control function, the 6 channel communication board port

number is the same as another port number. Alternatively, the port number (from 11 to 30) is out of

range (FIP3).

Remedy: Change the communication port number (Pressure control port no.) in Proper data (FIP3).

------------------------------

Code: 11022634

第 157 页

Display:

Used by: IP2,IP3

Cause: The value set in Proper Data item "Flux_st1_d_no" or "Flux_st2_d_no" is out of range.

Remedy: The valid range for these Proper Data items is 0 to 37 ("0" signifies that it is not used). After

correcting the Proper Data item in question, transmit the production program again.

------------------------------

Code: 11022635

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_H2.X" parameter in the IP2 Proper

data is set to 0. (When a rectangular nozzle is used with Holder 2, the nozzle inclination is found using

the "nozzle_size_H2.X" and "nozzle_size_H2.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

Code: 11022636

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_H3.X" parameter in the IP2 Proper

data is set to 0. (When a rectangular nozzle is used with Holder 3, the nozzle inclination is found using

the "nozzle_size_H3.X" and "nozzle_size_H3.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

Code: 11022637

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_H2.Y" parameter in the IP2 Proper

data is set to 0. (When a rectangular nozzle is used with Holder 2, the nozzle inclination is found using

the "nozzle_size_H2.X" and "nozzle_size_H2.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

Code: 11022638

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_H3.Y" parameter in the IP2 Proper

data is set to 0. (When a rectangular nozzle is used with Holder 3, the nozzle inclination is found using

the "nozzle_size_H3.X" and "nozzle_size_H3.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

Code: 11022639

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_1.Y" parameter in the IP2 Proper

data (i.e., the Y value for Nozzle 1 of the nozzle station) is set to 0. (When a rectangular nozzle is used as

Nozzle 1 of a nozzle station with a variable holder, the nozzle inclination is found using the

"nozzle_size_1.X" and "nozzle_size_1.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

第 158 页

------------------------------

Code: 1102263A

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_2.Y" parameter in the IP2 Proper

data (i.e., the Y value for Nozzle 2 of the nozzle station) is set to 0. (When a rectangular nozzle is used as

Nozzle 2 of a nozzle station with a variable holder, the nozzle inclination is found using the

"nozzle_size_2.X" and "nozzle_size_2.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

Code: 1102263B

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_3.Y" parameter in the IP2 Proper

data (i.e., the Y value for Nozzle 3 of the nozzle station) is set to 0. (When a rectangular nozzle is used as

Nozzle 3 of a nozzle station with a variable holder, the nozzle inclination is found using the

"nozzle_size_3.X" and "nozzle_size_3.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

Code: 1102263C

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_4.Y" parameter in the IP2 Proper

data (i.e., the Y value for Nozzle 4 of the nozzle station) is set to 0. (When a rectangular nozzle is used as

Nozzle 4 of a nozzle station with a variable holder, the nozzle inclination is found using the

"nozzle_size_4.X" and "nozzle_size_4.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

Code: 1102263D

Display: Same as code

Used by: IP2

Cause: Vision processing cannot be performed when the "nozzle_size_5.Y" parameter in the IP2 Proper

data (i.e., the Y value for Nozzle 5 of the nozzle station) is set to 0. (When a rectangular nozzle is used as

Nozzle 5 of a nozzle station with a variable holder, the nozzle inclination is found using the

"nozzle_size_5.X" and "nozzle_size_5.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

Code: 1102263E

Display: Same as code

Used by:

Cause: Vision processing cannot be performed when the "nozzle_size_6.Y" parameter in the IP2 Proper

data (i.e., the Y value for Nozzle 6 of the nozzle station) is set to 0. (When a rectangular nozzle is used as

Nozzle 6 of a nozzle station with a variable holder, the nozzle inclination is found using the

"nozzle_size_6.X" and "nozzle_size_6.Y" settings. Vision processing cannot be performed to find the

rectangular nozzle inclination when one of these nozzle size values has not been input.)

Remedy: Enter the correct nozzle size and retransmit the Proper data.

------------------------------

第 159 页