FUJI错误代码查询.pdf - 第1099页

Cause: The machine was not able to extend the in-carrier because there is a board on the in-lifter,but it was not sure whether there is a board clamped in the in-carrier. If the in-carrier has clamped a board with parts …

LX044: IN-carrier left front opened sensor

LX045: IN-carrier left rear opened sensor

LX046: IN-carrier right front opened sensor

LX047: IN-carrier right rear opened sensor

------------------------------

Code: 15010C03

Display: Board check error:I_CRRY

No brd on in-carrier Chk status of brd

Used by: CP643

Cause: An in-carrier board sensor has turned OFF (indicating that the first or second board is absent)

before the main lifter began loading boards from the in-carrier,after having indicated the presence of the

board in question when the in-carrier arrived at the extended limit.

Remedy: Adjust the in-carrier board sensors (the I/O input signals listed below) ensuring they correctly

detect the presence of boards clamped by the in-carrier.

I/O input signals:

LX018: In-carrier 1 board sensor

LX019: In-carrier 2 board sensor

------------------------------

Code: 15010C04

Display: Interlock alarm:I_CRRY

Chk conveyance brds between in-carrier and main conv.

Board check error:I_CRRY

In-carr brd conf sensor on Adj sensor so it turns off

Used by: CP643

Cause: The in-carrier board sensors are abnormal. ( For example,a sensor is ON even though it should be

OFF.

Remedy: Make sure the in-carrier board sensors (the I/O input signals listed below) tuen ON and OFF

correctly.

I/O input signals:

LX018: IN-carrier 1 board sensor

LX019: IN-carrier 2 board sensor

------------------------------

Code: 15010C05

Display: Cylinder cycle alarm:I_CRRY

I_CRRY board transfer time up

Used by: CP643

Cause: The in-carrier was extended,but the extended limit sensor did not turn

ON within the specified time.

The in-carrier was retracted,but the retracted limit sensor did not turn ON within the specified time.

The in-carrier extended and retracted limit sensors are both ON.

Remedy: Make sure the in-carrier extends and retracts smoothly.

Make sure the extended and retracted limit sensors have been attached at the correct positions.

Make sure the extended and retracted limit sensors (the I/O input signals listed below) turn ON and OFF.

Make sure the extended and retracted limit sensors (the I/O input signals listed below) turn ON and OFF

correctly when the in-carrier is extended and retracted.I/O input signals:

LX01C: IN-carrier extended limit sensor

LX01D: IN-carrier retracted limit sensor

------------------------------

Code: 15010C06

Display: Interlock alarm:I_CRRY

Used by: CP643

第 1098 页

Cause: The machine was not able to extend the in-carrier because there is a board on the in-lifter,but it

was not sure whether there is a board clamped in the in-carrier. If the in-carrier has clamped a board with

parts mounted on the reverse side, there may be interference between the board and the one in the in-

lifter.

The machine was not able to retract the in-carrier because there is a board on the in-lifter,and there is

also a board clamped in the extended in-carrier.if the board clamped in the in-carrir has parts mounted

on the reverse side,there may

be interference between this board and the one on the in-lifter.

The machine was not able to retract the in-carrier from a position between the extended limit and the

retracted limit because there is a board on the in-lifter,but it is not sure whether there is a board clamped

in the in-carrier.if the in-carrier has clamped a board with parts mounted on the reverse side,there may be

interference between this board and the one on the in-lifter.

Remedy: Remove any boards from in the in-lifter.

Make sure the in-lifter board arrival sensors (the I/O input signals listed below) detect the presence of

boards in the in-lifter.

I/O input signals:

LX003: IN1 board deceleration start point sensor

LX004: IN1 board arrival sensor

LX007: IN1/IN2 board gap sensor

LX008: IN2 board deceleration start point sensor

LX009: IN2 board arrival sensor

LX017: In-conveyor board load sensor

------------------------------

Code: 15010C07

Display: Interlock alarm:I_CRRY

In-carrier not at extended position.

Used by: CP643,CP643M

Cause: Main conveyor movement for the conveyance of board(s) was terminated because the in-carrier is

out of position.

Remedy: If the in-carrier is at its extended position, check the extended and clamping limit sensors.If the

extended and clamping limit sensors are on, the carrier may be moving too fast and has recoiled out of

position.If the carrier is not at its extended position the movement of the carrier itself may require

adjustment.

------------------------------

Code: 15010D01

Display: PCB Transport Error:O_CRRY

Brd status at out-carr not clear Chk brd status

Used by: CP643

Cause: The out-carrier loaded a board (or boards) from the XY-table and unloadeded them to the out-

lifter,but the board status (that is, first or second board presence) detected by the out-conveyor board

sensors was deffernt from the board status that was detected when the boards were loaded from XY-table.

The in-carrier board sensors detected only the second board when the board check was performed. ( For

example,the out-lifter board sensors detected only the second board,even though the out-carrier loaded

both the first board and the second board from the XY-table.)

The out-carrier board sensors detected only the second board when the board check was performed.

Remedy: Make sure the out-carrrier board sensors (the I/O input signals listed below) correctly detect the

presence of boards clamped by the out-carrier.

I/O input signals:

LX038 OUT-carrier 1 board sensor

LX039 OUT-carrier 2 board sensor

Make sure the out-conveyor board sensors (the I/O input signals listed below) correctly detect the

第 1099 页

presence of boards on the conveyor.

I/O input signals:

LX00E: OUT1 board arrival sensor

LX00F: OUT2 board arrival sensor

------------------------------

Code: 15010D02

Display: Board-clamper error:O_CRRY

Check board clamp/unclamp limits on the O_CRRY

Used by: CP643

Cause: The out-carrier was closed,but the closed sensor did not turn ON within the specified time.

The out-carrier was opened,but the opened sensor did not turn ON within specified time.

The out-carrier opened and closed sensors are both ON.

Remedy: Make sure the out-carrier opens and closes smoothly.

Make sure the opened and closed sensors have been attached at the correct positions.

Make sure the opened and closed sensors (the I/O input signals listed below) turn ON and OFF.

Make sure the opened and closed sensors (the I/O input signals listed below) turn ON and OFF correctly

when the out-carrier is opened and closed.

I/O input signals:

LX048: OUT-carrier left front closed sensor

LX049: OUT-carrier left rear closed sensor

LX04A: OUT-carrier right front closed sensor

LX04B: OUT-carrier right rear closed sensor

LX04C: OUT-carrier left front opened sensor

LX04D: OUT-carrier left rear opened sensor

LX04E: OUT-carrier right front opened sensor

LX04F: OUT-carrier right rear opened sensor

------------------------------

Code: 15010D03

Display: Board check error:O_CRRY

No brd on out-carrier Chk status of brd

Used by: CP643

Cause: An out-carrier board sensor did not confirm a board (that is,the sensor did not turn ON) loaded

onto the out-carrier from the main lifter.

An out-carrier board sensor has turned OFF (indicating that the first or second

board is absent) before the out carrier began retracting,after having indicated

the presence of the board in question when that board was loaded onto the out-carrier from main lifter.

An out-carrier board sensor has turned OFF (indicating that the first or second

board is absent) before the out-carrier began retracting,after having indicated

the presence of the board in question during a board check performed when the out-carrier was at the

extended limit.

Remedy: Adjust the out-carrier board sensors (the I/O input signals listed below) ensuring they correctly

detect the presence of boards clamped by the out-carrier.

I/O input signals:

LX038: Out-carrier 1 board sensor

LX039: Out-carrier 2 board sensor

------------------------------

Code: 15010D04

Display: Board check error:O_CRRY

Out-carr brd conf sensor on Adj sensor so it turns off

Used by: CP643

Cause: The out-carrier board sensors are abnormal. ( For example,a sensor is ON even though it should

第 1100 页